HP ZBook Studio x360 Maintenance and Service Guide - Page 157

Connector types, IMPORTANT, CAUTION

Get HP ZBook Studio x360 PDF manuals and user guides View all HP ZBook Studio x360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 157 highlights

Connector types IMPORTANT: Connector pins and connector gold fingers should not be touched directly with bare hands. There are several different types of connectors on the system board with different requirements for cable removal or insertion. Flex cable When connecting flex cables to a ZIF connector, rotate the latch to 90 degrees, push the cable completely, evenly into the connector, and then close the latch. When removing flex cables from a ZIF connector on the system board, the latch must be released before the cable can be removed. Always follow these steps: 1. Flip the connector latch 90 degrees to release the cable. 2. Grasp the cable end of the connector and pull it straight out. CAUTION: Always release connector latch before removing the cable. Otherwise, pulling the cable could damage the cable pins and result in a failed device. Horizontal installation cable Use flat tool to pull connector evenly. Do not pull on cable to remove. Slide connector into receptacle on same horizontal plane as board and use flat tool to push evenly into receptacle. Multi-pin horizontal insert connector (LVDS cable to display panel) Insert procedure: Additional information 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
Connector types
IMPORTANT:
Connector pins and connector gold
fingers
should not be touched directly with bare hands.
There are several
different
types of connectors on the system board with
different
requirements for cable
removal or insertion.
Flex cable
When connecting
flex
cables to a ZIF connector, rotate the latch to 90 degrees, push the cable completely,
evenly into the connector, and then close the latch.
When removing
flex
cables from a ZIF connector on the system board, the latch must be released before the
cable can be removed. Always follow these steps:
1.
Flip the connector latch 90 degrees to release the cable.
2.
Grasp the cable end of the connector and pull it straight out.
CAUTION:
Always release connector latch before removing the cable. Otherwise, pulling the cable could
damage the cable pins and result in a failed device.
Horizontal installation cable
Use
flat
tool to pull connector evenly. Do not pull on cable to remove.
Slide connector into receptacle on same horizontal plane as board and use
flat
tool to push evenly into
receptacle.
Multi-pin horizontal insert connector (LVDS cable to display panel)
Insert procedure:
Additional information
145