Xerox C2424 Service Manual - Page 144

Continued, Run the Paper Lead Edge Times test.

Page 144 highlights

Jam Code Troubleshooting Procedures (Continued) B2Q B3M B3N B3P B3Q B3S B3T C2C C2D C2E C2F C2K C2M C2N C2P C2Q C2R C2T The preheat flag tripped unexpectedly while the system was picking paper from Tray 1. 1. Test the preheat flag using the diagnostic Sensors test. 2. Ensure ground integrity of the system (see page 4-73). The preheat flag timed out waiting for the paper picked from Tray 2. The preheat flag timed out waiting for the paper picked from Tray 3. The preheat flag timed out waiting for the paper picked from Tray 4 The preheat flag timed out waiting for the paper picked from Tray 1. Preheater sensor timed out during stage. Preheater exit sensor timed out during transfix. 1. Verify that the media is appropriate for the tray. 2. Check for paper path obstructions, ensure the preheater plate moves freely. 3. Replace the Tray 1 Separator Pad Assembly. 4. Run diagnostics to test the preheat flag. 5. Ensure the deskew rollers are in good condition. 6. Run the Deskew Clutch test. 7. Run the Paper Path Drive test. 8. Replace the pre heater, then retest. Strip flag unexpected event during mechanical recovery. Strip flag unexpected state during warm-up. Strip flag unexpected event during system ready. Strip flag unexpected event during fault. Strip flag unexpected event during transfix roller oiling. The strip flag actuated unexpectedly when paper picked from Tray 2. The strip flag actuated unexpectedly when paper picked from Tray 3. The strip flag actuated unexpectedly when paper picked from Tray 4. The strip flag actuated unexpectedly when paper picked from Tray 1. Strip flag unexpected event during pick from the duplex path. Strip flag unexpected event during transfix. 1. Ensure ground integrity of the system (see page 4-73). 2. Check the paper tray for overfill. 3. Run the Stripper sensor test. 4. Inspect the stripper blade for damage or debris. 5. Run the Paper Lead Edge Times test. 6. Replace the stripper carriage assembly. 3-52 WorkCentre C2424 Service Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
  • 336
  • 337
  • 338
  • 339
  • 340
  • 341
  • 342
  • 343
  • 344
  • 345
  • 346
  • 347
  • 348
  • 349
  • 350
  • 351
  • 352
  • 353
  • 354
  • 355
  • 356
  • 357
  • 358
  • 359
  • 360
  • 361
  • 362
  • 363
  • 364
  • 365
  • 366
  • 367
  • 368
  • 369
  • 370
  • 371
  • 372
  • 373
  • 374
  • 375
  • 376
  • 377
  • 378
  • 379
  • 380
  • 381
  • 382
  • 383
  • 384
  • 385
  • 386
  • 387
  • 388
  • 389
  • 390
  • 391
  • 392
  • 393
  • 394
  • 395
  • 396
  • 397
  • 398
  • 399
  • 400
  • 401
  • 402
  • 403
  • 404
  • 405
  • 406
  • 407
  • 408
  • 409
  • 410
  • 411
  • 412
  • 413
  • 414
  • 415
  • 416
  • 417
  • 418
  • 419
  • 420
  • 421
  • 422
  • 423
  • 424
  • 425
  • 426
  • 427
  • 428
  • 429
  • 430
  • 431
  • 432

3-52
WorkCentre C2424 Service Manual
B2Q
The preheat flag tripped unexpectedly while the system was picking paper from
Tray 1.
1.
Test the preheat flag using the diagnostic Sensors test.
2.
Ensure ground integrity of the system (see page 4-73).
B3M
The preheat flag timed out waiting for the paper picked from Tray 2.
B3N
The preheat flag timed out waiting for the paper picked from Tray 3.
B3P
The preheat flag timed out waiting for the paper picked from Tray 4
B3Q
The preheat flag timed out waiting for the paper picked from Tray 1.
B3S
Preheater sensor timed out during stage.
B3T
Preheater exit sensor timed out during transfix.
1.
Verify that the media is appropriate for the tray.
2.
Check for paper path obstructions, ensure the preheater plate moves freely.
3.
Replace the Tray 1 Separator Pad Assembly.
4.
Run diagnostics to test the preheat flag.
5.
Ensure the deskew rollers are in good condition.
6.
Run the Deskew Clutch test.
7.
Run the Paper Path Drive test.
8.
Replace the pre heater, then retest.
C2C
Strip flag unexpected event during mechanical recovery.
C2D
Strip flag unexpected state during warm-up.
C2E
Strip flag unexpected event during system ready.
C2F
Strip flag unexpected event during fault.
C2K
Strip flag unexpected event during transfix roller oiling.
C2M
The strip flag actuated unexpectedly when paper picked from Tray 2.
C2N
The strip flag actuated unexpectedly when paper picked from Tray 3.
C2P
The strip flag actuated unexpectedly when paper picked from Tray 4.
C2Q
The strip flag actuated unexpectedly when paper picked from Tray 1.
C2R
Strip flag unexpected event during pick from the duplex path.
C2T
Strip flag unexpected event during transfix.
1.
Ensure ground integrity of the system (see page 4-73).
2.
Check the paper tray for overfill.
3.
Run the Stripper sensor test.
4.
Inspect the stripper blade for damage or debris.
5.
Run the Paper Lead Edge Times test.
6.
Replace the stripper carriage assembly.
Jam Code Troubleshooting Procedures
(Continued)