Poulan PR5020 Owner Manual - Page 1

Poulan PR5020 Manual

Get Poulan PR5020 PDF manuals and user guides View all Poulan PR5020 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

aa WARNING! Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury. Instruction Manual PR5020 NOTE: Your product may differ slightly from the item shown. Quick-Start Guide 1 6 Place right foot in rear handle as shown. Using right hand, pull starter rope sharply 5 times. Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of gasoline for a 50:1 mixture. Shake well. Pour into fuel tank. CAUTION: Do not use alternate fuels such as ethanol blends above 10% by volume (E-15, E-85) or any methanol blended fuel. 7 Push blue choke lever to half choke. 2 Add bar and chain oil to oil tank. 8 3 Make sure chain brake is off by pulling back the handguard. Pull starter rope until engine starts. 9 4 Slowly press primer bulb 10 times. Allow engine to warm for 30 seconds. Squeeze throttle trigger to set normal idle. 10 5 Pull blue choke lever out fully. Press red switch to STOP position when finished using saw. STARTING A WARM ENGINE 4+5+7+8 IMPORTANT: • Never let your saw chain come in contact with soil/dirt during operation. This will completely dull your chain and will require installation of a new chain. • Check your chain tension prior to each time you start the chainsaw. Check tension on a new chain after the first 15 minutes of operation. See the manual for chain tensioning instructions. 115817295 Rev. B 2016-05-05 LDAV50MC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
a
WARNING! Read and follow all Safety Rules and
Operating Instructions before using this product.
Failure to do so can result in serious injury.
Instruction Manual
PR5020
Quick-Start Guide
NOTE: Your product may differ slightly from the
item shown.
1
Mix 2.6 oz. of full synthetic 2-Cycle Oil with 1 gallon of gasoline for a
50:1 mixture. Shake well. Pour into fuel tank.
CAUTION: Do not use alternate fuels such as ethanol blends above
10% by volume (E-15, E-85) or any methanol blended fuel.
2
Add bar and chain oil to
oil tank.
3
Make sure chain brake
is off by pulling back the
handguard.
4
Slowly press primer bulb
10 times.
5
Pull blue choke lever out
fully.
6
Place right foot in rear
handle as shown. Using
right hand, pull starter rope
sharply 5 times.
7
Push blue choke lever to
half choke.
8
Pull starter rope until engine
starts.
9
Allow engine to warm for 30
seconds. Squeeze throttle
trigger to set normal idle.
10
Press red switch to STOP
position when fnished
using saw.
STARTING A WARM ENGINE
4 + 5 + 7 + 8
IMPORTANT:
•
Never let your saw chain come in contact with soil/dirt during operation. This will completely dull your chain and will
require installation of a new chain.
• Check your chain tension prior to each time you start the chainsaw. Check tension on a new chain after the Frst 15
minutes of operation. See the manual for chain tensioning instructions.
LDAV50MC
115817295
Rev. B
2016-05-05