2015 Polaris Victory Vision Owners Manual - Page 68

2015 Polaris Victory Vision Manual

Get 2015 Polaris Victory Vision PDF manuals and user guides View all 2015 Polaris Victory Vision manuals

Page 68 highlights

Maintenance Drive Belt Tension Inspection 1. Elevate and support the motorcycle with the rear tire slightly off the floor. CAUTION! Make sure the motorcycle is stable when elevated. Injury may occur if the motorcycle tips or falls. 2. Place the transmission in neutral. 3. Rotate the rear wheel in a forward direction until the valve stem is at the bottom. This is your reference point for determining the tight spot to make your adjustment (if necessary). 4. Position the small O-ring on the tension gauge directly over the 10 lbs. mark on the plunger. 5. Place a tape measure or steel rule next to the drive belt, mid-way between the sprockets. Support the rule or tape so it does not move. 6. Note the graduation mark on the rule that aligns with the lower edge of the belt. This position represents zero force. 7. Place the support base of the tension gauge squarely against the lower surface of the belt as close as possible to the rule or tape. 8. Keeping the tension gauge perpendicular to the belt surface and parallel with its length, push the plunger upward until the small O-ring touches the tension gauge body. 9. Be sure the tension gauge is seated squarely against the belt, and note the graduation mark on the rule that now aligns with the lower edge of the belt. This position represents 10 lbs. force. 10. To calculate belt tension (deflection) subtract the smaller measurement from the larger measurement and record it. Determine The Tightest Spot 11. Repeat the above deflection measurements with the tire's valve stem at the rear most position, top, and front most positions (90 degrees rotation each time), recording each measurement. 12. If the tightest measurement is not within the recommended range (see page 65), belt tension must be adjusted. Drive Belt Belt Tension Gauge Rule 90° Drive Belt Push Inner Plunger 90q Rear Wheel 90q 90q Valve Stem 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
66
Maintenance
Drive Belt Tension Inspection
1.
Elevate and support the motorcycle with the rear tire
slightly off the floor.
CAUTION!
Make sure the motorcycle is stable when elevated.
Injury may occur if the motorcycle tips or falls.
2.
Place the transmission in neutral.
3.
Rotate the rear wheel in a forward direction until the
valve stem is at the bottom. This is your reference point
for determining the tight spot to make your adjustment
(if necessary).
4.
Position the small O-ring on the tension gauge directly
over the 10 lbs. mark on the plunger.
5.
Place a tape measure or steel rule next to the drive belt,
mid-way between the sprockets. Support the rule or
tape so it does not move.
6.
Note the graduation mark on the rule that aligns with
the lower edge of the belt. This position represents
zero
force
.
7.
Place the support base of the tension gauge squarely
against the lower surface of the belt as close as possible
to the rule or tape.
8.
Keeping the tension gauge perpendicular to the belt
surface and parallel with its length, push the plunger
upward until the small O-ring touches the tension
gauge body.
9.
Be sure the tension gauge is seated squarely against the
belt, and note the graduation mark on the rule that now
aligns with the lower edge of the belt. This position
represents
10 lbs. force
.
10.
To calculate belt tension (deflection) subtract the
smaller measurement from the larger measurement and
record it.
Determine The Tightest Spot
11.
Repeat the above deflection measurements
with the tire’s valve stem at the rear most
position, top, and front most positions (90
degrees rotation each time), recording each
measurement.
12.
If the
tightest
measurement is not within the
recommended range (see page 65), belt ten-
sion must be adjusted.
Belt Tension Gauge
Rule
Drive Belt
Push Inner Plunger
90
±
Drive Belt
90
q
90
q
90
q
Valve Stem
Rear Wheel