2015 Polaris Victory Vision Owners Manual - Page 39

2015 Polaris Victory Vision Manual

Get 2015 Polaris Victory Vision PDF manuals and user guides View all 2015 Polaris Victory Vision manuals

Page 39 highlights

Instruments, Features and Controls Pedal Adjustment The brake pedal and gear shift pedal controls can be adjusted to a front, rear or center position. The center position is the factory setting. Tip: An accessory linkage rod is needed to fully adjust the gear shift pedal control. 1. Remove the screw from the footwell support. Tool: 6 mm Allen wrench 2. Slide the control forward or rearward in its track until the threaded hole of the control aligns with the desired hole in the footrest support. 3. Reinstall the screw. Torque: 96 in-lbs (11 Nm) 4. After adjusting the shift pedal, always readjust the shift linkage rod. Loosen both jam nuts on the linkage and turn the shaft until the footpeg is about 90 mm from the floorboard (or to desired height). Tighten both jam nuts. Torque: 96 in-lbs (11 Nm). Center Adjustment Position Windshield Adjustment Use the motorized windshield adjustment switch (if equipped) to adjust the windshield. See page 31. If the motorcycle is not equipped with this feature, you can manually adjust the windshield. 1. Park the motorcycle on a firm, level surface. Turn the key to the OFF position. 2. Remove the windshield trim panel. See page 85. 3. Remove the retaining clip. 4. Hold slight downward pressure on the bottom of the windshield (it is under slight upward spring pressure). Remove the clevis pin. 5. Slide the windshield inner bracket to align with one of the optional holes in the outer bracket. Reinstall the clevis pin. Reinstall the retaining clip in the clevis pin. 6. Reinstall the windshield trim panel. Retaining Clip Clevis Pin 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
37
Instruments, Features and Controls
Pedal Adjustment
The brake pedal and gear shift pedal controls can be adjusted
to a front, rear or center position. The center position is the
factory setting.
Tip:
An accessory linkage rod is needed to fully adjust the gear shift
pedal control.
1.
Remove the screw from the footwell support.
Tool:
6 mm Allen wrench
2.
Slide the control forward or rearward in its track until
the threaded hole of the control aligns with the desired
hole in the footrest support.
3.
Reinstall the screw.
Torque:
96 in-lbs (11 Nm)
4.
After adjusting the shift pedal, always readjust the shift
linkage rod. Loosen both jam nuts on the linkage and
turn the shaft until the footpeg is about 90 mm from the
floorboard (or to desired height). Tighten both jam nuts.
Torque:
96 in-lbs (11 Nm).
Windshield Adjustment
Use the motorized windshield adjustment switch (if
equipped) to adjust the windshield. See page 31. If the motor-
cycle is not equipped with this feature, you can manually
adjust the windshield.
1.
Park the motorcycle on a firm, level surface. Turn the key
to the OFF position.
2.
Remove the windshield trim panel. See page 85.
3.
Remove the retaining clip.
4.
Hold slight downward pressure on the bottom of the
windshield (it is under slight upward spring pressure).
Remove the clevis pin.
5.
Slide the windshield inner bracket to align with one of the
optional holes in the outer bracket. Reinstall the clevis
pin. Reinstall the retaining clip in the clevis pin.
6.
Reinstall the windshield trim panel.
Center Adjustment
Position
Retaining Clip
Clevis Pin