Lantronix EDS2100 EDS1100 / EDS2100 - User Guide - Page 71

To con PPP, Line1, PPP Configuration, Submit., PPP Configuration Settings

Get Lantronix EDS2100 PDF manuals and user guides View all Lantronix EDS2100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

10: Service Settings Note: The following section describes the steps to configure PPP 1 (PPP on serial line 1); these steps also apply to any line instance of the device. To configure PPP: 1. Click PPP on the menu bar and Line1 at the top of the page. The PPP on Line 1 - Configuration page appears. Figure 10-2 PPP Configuration Settings 2. Enter or modify the following settings: PPP Configuration Settings Local IP Address Peer IP Address Authentication Mode Username Password 3. Click Submit. Table 10-3 PPP Configuration Description Enter the IP address assigned to the device's PPP interface. Enter the IP address assigned to the peer (when requested during negotiation). Choose the authentication mode:  None = no authentication is required  PAP = Password Authentication Protocol  CHAP = Challenge Handshake Authentication Protocol  MS-CHAP = Microsoft Challenge-Handshake Authentication Protocol  MS-CHAPV2 = Microsoft Challenge-Handshake Authentication Protocol Version 2 Enter a username if authentication is to be used on the PPP interface. The peer must be configured to use the same username. Enter a password if authentication is to be used on the PPP interface. The peer must be configured to use the same password. EDS1100/2100 User Guide 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
10: Service Settings
EDS1100/2100 User Guide
71
Note:
The following section describes the steps to configure PPP 1 (PPP on serial line
1); these steps also apply to any line instance of the device.
To configure PPP:
1.
Click
PPP
on the menu bar and
Line1
at the top of the page. The PPP on Line 1 –
Configuration page appears.
Figure 10-2
PPP Configuration Settings
2.
Enter or modify the following settings:
Table 10-3
PPP Configuration
3.
Click
Submit.
PPP Configuration Settings
Description
Local IP Address
Enter the IP address assigned to the device’s PPP interface.
Peer IP Address
Enter the IP address assigned to the peer (when requested during
negotiation).
Authentication Mode
Choose the authentication mode:
None
= no authentication is required
PAP
= Password Authentication Protocol
CHAP
= Challenge Handshake Authentication Protocol
MS-CHAP
= Microsoft Challenge-Handshake Authentication
Protocol
MS-CHAPV2
= Microsoft Challenge-Handshake Authentication
Protocol Version 2
Username
Enter a username if authentication is to be used on the PPP
interface.
The peer must be configured to use the same username.
Password
Enter a password if authentication is to be used on the PPP
interface. The peer must be configured to use the same password.