Lantronix EDS2100 EDS1100 / EDS2100 - User Guide - Page 45

Line Command Mode, To con Line 1, Line 1 > Command, CP Group

Page 45 highlights

Line Command Mode Setting Command Mode enables the CLI on the serial line. To configure Line 1 Command Mode: 1. Click Line 1 > Command Mode at the top of the page. The Line 1 Command Mode page appears. Note: The CP Group option displayed in the screenshot is only supported in XPort Pro and XPort AR. 8: Line and Tunnel Settings Figure 8-4 Line 1 Command Mode 2. Enter or modify the following settings: Line - Command Mode Settings Mode Wait Time Table 8-5 Line 1 Command Mode Description Select the method of enabling Command Mode or choose to disable Command Mode.  Always = immediately enables Command Mode for the serial line.  Use Serial String = enables Command Mode when the serial string is read on the serial line during boot time.  Use CP Group = enables Command Mode based on the status of a CP Group. When the value matches the current value of the group, Command Mode is enabled on the serial line.  Use both Serial String and CP Group = the serial string and the value of the CP group must be matched to enable Command Mode.  Disabled = turns off Command Mode. Enter the wait time for the serial string during boot-up in milliseconds. EDS1100/2100 User Guide 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152

8: Line and Tunnel Settings
EDS1100/2100 User Guide
45
2.
Enter or modify the following settings:
Table 8-5
Line 1 Command Mode
Line Command Mode
Setting Command Mode
enables the CLI on the serial
line.
To configure Line 1
Command Mode:
1.
Click
Line 1 > Command
Mode
at the top of the
page. The Line 1
Command Mode page
appears.
Figure 8-4
Line 1 Command Mode
Line – Command Mode
Settings
Description
Mode
Select the method of enabling Command Mode or choose to disable
Command Mode.
Always
= immediately enables Command Mode for the serial line.
Use Serial String
= enables Command Mode when the serial string is
read on the serial line during boot time.
Use CP Group
= enables Command Mode based on the status of a CP
Group. When the value matches the current value of the group,
Command Mode is enabled on the serial line.
Use both Serial String and CP Group
= the serial string and the value of
the CP group must be matched to enable Command Mode.
Disabled
= turns off Command Mode.
Wait Time
Enter the wait time for the serial string during boot-up in milliseconds.
Note:
The
CP Group
option
displayed in the screenshot is
only supported in XPort Pro
and XPort AR.