Kyocera TASKalfa Pro 15000c Pro 15000c Command Center RX User Guide - Page 75

HP Web Jetadmin Compatibility, Read Only User

Get Kyocera TASKalfa Pro 15000c PDF manuals and user guides View all Kyocera TASKalfa Pro 15000c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Management Settings sysLocation The MIB-II sysLocation object. Usually this is the location information of the machine which is described under Location of System Settings page. Go to the System Settings page under Device Settings to modify the settings. HP Web Jetadmin Compatibility Turns HP Web Jetadmin Compatibility On or Off. After you have changed the setting, you must restart the machine. Authentication Traps Specifies whether to use authentication traps. If enabled (On), an SNMP trap is generated when an attempt to read or write is made using an incorrect community name. The trap is sent to the configured trap address. After you have changed the setting, you must restart the machine. Trap Recipient Click Settings button to finalize the settings. 3. Configure SNMPv3 as follows. After you have changed the setting, you must restart the machine. SNMPv3 Sets whether to use the SNMPv3 protocol. Select either On or Off in the Protocol Settings page under Network Settings. To configure SNMP v3, proceed as follows. Authentication Sets whether the user authentication is performed in SNMP communication. Hash Select either MD5 or SHA1 for Hash algorithm. This item becomes active when the Authentication is set to On. Privacy Sets whether to encrypt the communicated data in SNMP communication. This becomes available when Authentication is set to On. Encryption Select either DES or AES for encryption algorithm. This item becomes active when the Authentication is set to On. Read Only User Enter User Name and Password of the read-only user. Read/Write User Enter User Name and Password of the read/write user. 4. Click Submit button. User Guide 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Management Settings
User Guide
71
sysLocation
The MIB-II sysLocation object. Usually this is the location information of the
machine which is described under
Location
of
System Settings
page. Go to the
System Settings
page under
Device Settings
to modify the settings.
HP Web Jetadmin Compatibility
Turns HP Web Jetadmin Compatibility
On
or
Off
. After you have changed the set-
ting, you must restart the machine.
Authentication Traps
Specifies whether to use authentication traps. If enabled (
On
), an SNMP trap is
generated when an attempt to read or write is made using an incorrect community
name. The trap is sent to the configured trap address. After you have changed the
setting, you must restart the machine.
Trap Recipient
Click
Settings
button to finalize the settings.
3.
Configure
SNMPv3
as follows. After you have changed the setting, you must restart the
machine.
SNMPv3
Sets whether to use the SNMPv3 protocol. Select either
On
or
Off
in the
Protocol
Settings
page under
Network Settings
. To configure SNMP v3, proceed as fol-
lows.
Authentication
Sets whether the user authentication is performed in SNMP communication.
Hash
Select either
MD5
or
SHA1
for Hash algorithm. This item becomes active when the
Authentication is set to
On
.
Privacy
Sets whether to encrypt the communicated data in SNMP communication. This
becomes available when Authentication is set to
On
.
Encryption
Select either
DES
or
AES
for encryption algorithm. This item becomes active when
the Authentication is set to
On
.
Read Only User
Enter
User Name
and
Password
of the read-only user.
Read/Write User
Enter
User Name
and
Password
of the read/write user.
4.
Click
Submit
button.