Kyocera TASKalfa Pro 15000c Pro 15000c Command Center RX User Guide - Page 47

Network Settings, General, TCP/IP, TCP/IP Settings

Get Kyocera TASKalfa Pro 15000c PDF manuals and user guides View all Kyocera TASKalfa Pro 15000c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

8 Network Settings Network Settings General TCP/IP If needed, make the following settings: See below for detailed information. • General • TCP/IP • Protocols This section includes basic settings for networking. 1. Click General under Network Settings on the navigation menu. The General page opens. 2. The current communication status is shown in Host Name. Configure the host name on the System Settings page of Device Settings. 3. The host name is shown in NetBIOS Name. You can modify the name as necessary. 4. Select Auto, 10BASE-Half, 10BASE-Full, 100BASE-Half, 100BASE-Full and 1000BASE-T from the LAN Interface drop-down list depending on your network environment. 5. The current status is shown in Client Certificate. To make advanced settings, click Settings button. Select the appropriate certificate on the Certificate Settings page that will open. When you click Certificates, its content is displayed. Click Submit button. Configure the device certificate on the Certificates page. 6. Click Submit button. This section includes advanced settings for the TCP/IP protocol. * If the settings for the item marked with an asterisk (*) has been changed, you must restart the machine or the network. To restart the machine, proceed to the Reset page. 1. Click TCP/IP under Network Settings on the navigation menu. The TCP/IP Settings page opens. 2. Select On to use TCP/IP. 3. When an IP address that was mapped by the DNS server has been changed, Dynamic DNS automatically remaps the host name to the IP address. To activate the Dynamic DNS Settings, set Dynamic DNS to On. 4. Click Submit button. User Guide 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Network Settings
User Guide
43
8
Network Settings
If needed, make the following settings: See below for detailed information.
•
General
•
TCP/IP
•
Protocols
General
This section includes basic settings for networking.
1.
Click
General
under
Network Settings
on the navigation menu. The
General
page
opens.
2.
The current communication status is shown in
Host Name
. Configure the host name on
the
System Settings
page of
Device Settings
.
3.
The host name is shown in NetBIOS Name. You can modify the name as necessary.
4.
Select
Auto
,
10BASE-Half
,
10BASE-Full
,
100BASE-Half
,
100BASE-Full
and
1000BASE-T
from the
LAN Interface
drop-down list depending on your network
environment.
5.
The current status is shown in
Client Certificate
. To make advanced settings, click
Settings
button. Select the appropriate certificate on the
Certificate Settings
page that
will open. When you click
Certificates
, its content is displayed.
Click
Submit
button.
Configure the device certificate on the
Certificates
page.
6.
Click
Submit
button.
TCP/IP
This section includes advanced settings for the TCP/IP protocol.
* If the settings for the item marked with an asterisk (*) has been changed, you must
restart the machine or the network. To restart the machine, proceed to the
Reset
page.
1.
Click
TCP/IP
under
Network Settings
on the navigation menu. The
TCP/IP Settings
page opens.
2.
Select
On
to use TCP/IP.
3.
When an IP address that was mapped by the DNS server has been changed, Dynamic
DNS automatically remaps the host name to the IP address. To activate the Dynamic
DNS Settings, set
Dynamic DNS
to
On
.
4.
Click
Submit
button.