Dell DSS 2500 Owners Manual - Page 83

Installing the (optional) 2.5 inch internal hard drive cage, Prerequisites, Steps

Get Dell DSS 2500 PDF manuals and user guides View all Dell DSS 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Installing the (optional) 2.5 inch internal hard drive carrier on page 78 Installing the cooling shroud on page 60 Installing the internal PERC riser on page 95 Installing the dual riser module (optional) on page 93 After working inside your system on page 54 Installing the (optional) 2.5 inch internal hard drive cage Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system. 3. Keep the Phillips #2 screwdriver ready. 4. If connected, disconnect the cables from expansion card(s). 5. If required, remove the PCIe expansion card riser. NOTE: If applicable, close the expansion card latch on the cooling shroud to release the full length card. 6. Remove the cooling shroud. 7. Disconnect the power and data cables from the hard drive. 8. Disconnect the FAN1 cable from the power interposer board. NOTE: The FAN1 cable is routed behind the internal hard drive cage. Steps 1. Align the internal hard drive cage guide with the guide slots on the chassis. 2. Insert the internal hard drive cage into the chassis. 3. Install the screw to secure the internal hard drive cage to the chassis. Installing and removing system components 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
Installing the (optional) 2.5 inch internal hard drive carrier
on page 78
Installing the cooling shroud
on page 60
Installing the internal PERC riser
on page 95
Installing the dual riser module (optional)
on page 93
After working inside your system
on page 54
Installing the (optional) 2.5 inch internal hard drive cage
Prerequisites
1.
Follow the safety guidelines listed in the Safety instructions section.
2.
Follow the procedure listed in the Before working inside your system.
3.
Keep the Phillips #2 screwdriver ready.
4.
If connected, disconnect the cables from expansion card(s).
5.
If required, remove the PCIe expansion card riser.
NOTE:
If applicable, close the expansion card latch on the cooling shroud to release the full length card.
6.
Remove the cooling shroud.
7.
Disconnect the power and data cables from the hard drive.
8.
Disconnect the FAN1 cable from the power interposer board.
NOTE:
The FAN1 cable is routed behind the internal hard drive cage.
Steps
1.
Align the internal hard drive cage guide with the guide slots on the chassis.
2.
Insert the internal hard drive cage into the chassis.
3.
Install the screw to secure the internal hard drive cage to the chassis.
Installing and removing system components
83