Dell DSS 2500 Owners Manual - Page 131

Installing the left control panel

Get Dell DSS 2500 PDF manuals and user guides View all Dell DSS 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

3. Keep the T15 Torx screwdriver ready. Steps 1. Fold the PPID label around the cable. 2. Fold the pull tab close to the connector and guide the connector and pull tab into the channel. 3. Push the cable until the cable passes completely through the channel. 4. Tighten the screws to secure the left control panel to the chassis. NOTE: You must route the cable properly to prevent it from being pinched or crimped. 5. Connect the cable connector to the hard drive backplane by pushing on the center of the connector. Figure 73. Installing the left control panel 1. screw (3) 3. hard drive backplane 5. left control panel connector on hard drive backplane 2. left control panel 4. left control panel connector 6. plastic pull tab Next steps Follow the procedure listed in the After working inside your system section. Related references Safety instructions on page 53 Related tasks Before working inside your system on page 53 Removing the left control panel on page 129 After working inside your system on page 54 Installing and removing system components 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
3.
Keep the T15 Torx screwdriver ready.
Steps
1.
Fold the PPID label around the cable.
2.
Fold the pull tab close to the connector and guide the connector and pull tab into the channel.
3.
Push the cable until the cable passes completely through the channel.
4.
Tighten the screws to secure the left control panel to the chassis.
NOTE:
You must route the cable properly to prevent it from being pinched or crimped.
5.
Connect the cable connector to the hard drive backplane by pushing on the center of the connector.
Figure 73. Installing the left control panel
1.
screw (3)
2.
left control panel
3.
hard drive backplane
4.
left control panel connector
5.
left control panel connector on hard drive backplane
6.
plastic pull tab
Next steps
Follow the procedure listed in the After working inside your system section.
Related references
Safety instructions
on page 53
Related tasks
Before working inside your system
on page 53
Removing the left control panel
on page 129
After working inside your system
on page 54
Installing and removing system components
131