Adaptec 2930U User Guide - Page 36

Removing the SCSI Card 2930CU - scsi drivers

Get Adaptec 2930U - AHA Storage Controller Ultra SCSI 20 MBps PDF manuals and user guides
UPC - 760884155530
View all Adaptec 2930U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Installing Drivers 10 Press Enter to continue the Windows NT operating system set-up. Follow the instructions on-screen and in the Windows NT documentation to complete the installation. Removing the SCSI Card 2930CU If you physically remove your SCSI Card 2930CU, a warning message is generated every time you boot Windows NT. To eliminate the warning message, remove the driver from your system. ! Caution: If you have removed a SCSI card but still have other SCSI cards of the same type installed in your computer, do not use Windows NT Setup to remove the device driver. To remove a driver from Windows NT 1 From the Control Panel, double-click SCSI Adapters. 2 Click the Drivers tab. 3 Select the driver (aic78xx.sys). 4 Click Remove. 5 Ensure that you are removing the correct driver, then click Yes. 6 Click Yes to restart the computer and initialize changes. Click No to return to the SCSI Adapters window. Note: Windows NT Setup does not delete the device driver from your system disk; it only updates Windows NT software configuration information so that the device driver is no longer loaded during system bootup. 4-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
4-14
Installing Drivers
10
Press
Enter
to continue the Windows NT operating system
set-up. Follow the instructions on-screen and in the Windows
NT documentation to complete the installation.
Removing the SCSI Card 2930CU
If you physically remove your SCSI Card 2930CU, a warning
message is generated every time you boot Windows NT. To eliminate
the warning message, remove the driver from your system.
Caution:
If you have removed a SCSI card but still have other
SCSI cards of the same type installed in your computer,
do not
use Windows NT Setup to remove the device driver.
To remove a driver from Windows NT
1
From the Control Panel, double-click
SCSI Adapters
.
2
Click the
Drivers
tab.
3
Select the driver (
aic78xx.sys
).
4
Click
Remove
.
5
Ensure that you are removing the correct driver, then click
Yes
.
6
Click
Yes
to restart the computer and initialize changes. Click
No
to return to the SCSI Adapters window.
Note:
Windows NT Setup does not delete the device driver
from your system disk; it only updates Windows NT software
configuration information so that the device driver is no
longer loaded during system bootup.
!