Adaptec 2930U User Guide - Page 21

Connecting External SCSI Devices - 2930cu scsi card

Get Adaptec 2930U - AHA Storage Controller Ultra SCSI 20 MBps PDF manuals and user guides
UPC - 760884155530
View all Adaptec 2930U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Installing SCSI Devices Connecting External SCSI Devices The SCSI Card 2930CU has one 50-pin high-density external connector. You will need a high-quality 50-pin high-density external SCSI cable for each external SCSI device you are connecting. External SCSI cables are not included in the SCSI Card 2930CU kit. Refer to Chapter D, Obtaining SCSI Cables for more information. To connect external SCSI devices 1 Ensure that each external SCSI device has a unique SCSI ID from 0 to 6. For most external SCSI devices, the SCSI ID is set with a switch on the back of the device, as shown. Refer to the SCSI device's documentation for instructions on setting the SCSI ID. Note: Each device connected to your SCSI Card 2930CU (both internal and external) must have a unique SCSI ID from 0 to 6. You cannot use the same SCSI ID twice. SCSI ID 2 If your computer is running, turn it off and disconnect the power cord. 3 Connect one end of an external SCSI cable to the SCSI Card 2930CU external SCSI connector. Secure the cable by tightening the screws on the cable connector. Note: Avoid touching the device connector pins. 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
3-5
Installing SCSI Devices
Connecting External SCSI Devices
The SCSI Card 2930CU has one 50-pin high-density external
connector. You will need a high-quality 50-pin high-density
external SCSI cable for each external SCSI device you are
connecting. External SCSI cables are not included in the SCSI Card
2930CU kit. Refer to
Chapter D,
Obtaining SCSI Cables
for more
information.
To connect external SCSI devices
1
Ensure that each external SCSI device has a unique SCSI ID from 0
to 6.
For most external SCSI devices, the SCSI ID is set with a
switch on the back of the device, as shown. Refer to the SCSI
device’s documentation for instructions on setting the SCSI ID.
Note:
Each device connected to your SCSI Card 2930CU
(both internal and external) must have a unique SCSI ID
from 0 to 6. You cannot use the same SCSI ID twice.
2
If your computer is running, turn it off and disconnect the power
cord.
3
Connect one end of an external SCSI cable to the SCSI Card 2930CU
external SCSI connector. Secure the cable by tightening the
screws on the cable connector.
Note:
Avoid touching the device connector pins.
SCSI ID