Adaptec 2930U User Guide - Page 34

Installing the Driver When Installing Windows NT to a SCSI - 2930 windows 7

Get Adaptec 2930U - AHA Storage Controller Ultra SCSI 20 MBps PDF manuals and user guides
UPC - 760884155530
View all Adaptec 2930U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Installing Drivers Installing the Driver When Installing Windows NT The driver is embedded on the Windows NT 4.0 CD. During a normal Windows NT installation, the SCSI Card 2930CU is detected in your system and the embedded driver is automatically installed. Installing the Driver When Windows NT is Already Installed To update or install the drivers if Windows NT is already installed 1 Start Windows NT. 2 Click Start, point to Settings, then click Control Panel. 3 Double-click SCSI Adapters, then click the Drivers tab. 4 Click Add. 5 In the Install Driver window, click Have Disk. 6 Insert the SCSI Card 2930 CD into the CD-ROM drive. 7 In the Copy Manufacturer's File From text box, type the drive letter for your CD-ROM drive, and click OK. 8 In the Install Driver window, Click OK. The system asks if you want to use the currently installed driver or install a new one. 9 Click New. 10 Type the drive letter for your CD-ROM drive, then click Continue. The driver is now installed. 11 Restart your computer for the changes to take effect. Installing the Driver When Installing Windows NT to a SCSI Hard Disk Drive Attached to the SCSI Card 2930CU Follow the appropriate set of instructions for a fresh Windows NT installation from either CD or floppy disk. Completing an Installation from CD 1 Insert your Windows NT 4.0 CD into your CD-ROM drive, then turn on your computer. 2 Press and release F6 immediately when this message appears: Setup is inspecting your computer's hardware configuration... 4-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
4-12
Installing Drivers
Installing the Driver When Installing Windows NT
The driver is embedded on the Windows NT 4.0 CD. During a
normal Windows NT installation, the SCSI Card 2930CU is detected
in your system and the embedded driver is automatically installed.
Installing the Driver When Windows NT is Already Installed
To update or install the drivers if Windows NT is already installed
1
Start Windows NT.
2
Click
Start
, point to
Settings
, then click
Control Panel
.
3
Double-click
SCSI Adapters
, then click the Drivers tab.
4
Click
Add
.
5
In the Install Driver window, click
Have Disk
.
6
Insert the SCSI Card 2930 CD into the CD-ROM drive.
7
In the Copy Manufacturer’s File From text box, type the drive
letter for your CD-ROM drive, and click
OK
.
8
In the Install Driver window, Click
OK
.
The system asks if you want to use the currently installed driver
or install a new one.
9
Click
New
.
10
Type the drive letter for your CD-ROM drive, then click
Continue
.
The driver is now installed.
11
Restart your computer for the changes to take effect.
Installing the Driver When Installing Windows NT to a SCSI
Hard Disk Drive Attached to the SCSI Card 2930CU
Follow the appropriate set of instructions for a fresh Windows NT
installation from either CD or floppy disk.
Completing an Installation from CD
1
Insert your Windows NT 4.0 CD into your CD-ROM drive, then
turn on your computer.
2
Press and release
F6
immediately
when this message appears:
Setup is inspecting your computer’s hardware configuration...