Denon AVR-2802 Owners Manual - Page 19
Clearing, learned, remote control signals, Storing signals, Clearing system call settings, NOTES - remote code
View all Denon AVR-2802 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
(3) Storing signals 1,5 2 START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B 3 VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND RDS MODE PTY MEMORY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP (4) Clearing system call settings 1,3 2 START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND RDS MODE PTY MEMORY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP Clearing "learned" remote control signals 1 Press the USE/LEARN selector button with the tip of a pen, etc., to set the learn mode. 2 To clear "learned" remote control signals, set the slide switch to the position at which the signals were "learned". AUDIO AVR/AVC VIDEO 1 1 Press the SET button. • The START LED and LEARNED/TX LED both Press the SET button. flash. SET SET 2 Press the button whose settings you want to clear. 2 Press the button at which you want to store the system call signals. • The START LED flashes. 3 Press the SET button. • The button is reset to the settings shown on 3 Set the mode switch to the position for the component whose remote control signals you want to store. the table on page 18. SET AUDIO TAPE CDR/MD CD MULTI AVR/AVC VIDEO DVD TV VDP VCR 4 Press the buttons whose remote control signals you want to store one by one. 5 Press the SET button. SET 3 Set the slide switch to the position at which the signals were "learned". TAPE CDR/MD CD MULTI DVD TV VDP VCR 4 Press the SYSTEM CALL SET button, and hold it in for at least four seconds. • When both the START and LEARNED/TX LEDs light simultaneously, all the stored codes are cleared. Light SET 5 Press the USE/LEARN selector button. ENGLISH 4 START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B 2 1,5 VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND MODE MEMORY RDS PTY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP 3 NOTES: • The remote control signals for the buttons pressed while storing the system call signals are transmitted when the buttons are pressed, so cover the remote sensor or take other measures so that the components do not operate while the signals are being stored. • The LEARNED/TX LED does not light if system call signals cannot be stored at the button that you have pressed or if you have already stored the maximum number of signals. 19