Denon AVR-2802 Owners Manual - Page 16

ENGLISH Preset memory (Audio component) • DENON components can be operated by setting the preset memory for CDR or MD. Operation is not possible for some models, however. In this case use the learning function (see page 18) to store the remote control signals. • For instructions on clearing the presettings stored in the preset memory, see page 19. Preset memory (Video component) • DENON and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not possible for some models, however. In this case use the learning function (see page 18) to store the remote control signals. • For instructions on clearing the presettings stored in the preset memory, see page 19. 1 AUDIO Set the slide switch to "AUDIO". AVR/AVC VIDEO 2 TAPE CDR/MD Set the slide switch to "CDR/MD". CD MULTI DVD TV VDP VCR 3 Holding in the POWER button, press the button for the components you want to set. START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B 3 1 VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND RDS MODE PTY MEMORY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP 3 2 1 AUDIO Set the slide switch to "VIDEO". AVR/AVC VIDEO 2 TAPE CDR/MD Set the slide switch to the component to be CD MULTI registered (DVD, VDP, VCR or TV). . DVD TV VDP VCR ( ) Keep the POWER button pressed in when performing steps 3 and 4 3 Holding in the POWER button, press the button for the corresponding manufacturer in block A. (Refer to Table 1.) Flashes 3 START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B 3,4 1 VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND RDS MODE PTY MEMORY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP 4 2 The LEARNED/TX LED flashes. "CDR/MD" Combinations of Personal System Codes DIRECT STEREO EXT.IN (DIRECT) (STEREO) (EXT. IN) (POWER) ON/SOURCE DENON CDR A DENON CDR B DENON MD Preset codes set upon shipment from the factory. The LEARNED/TX LED flashes. 4 Next, while holding the POWER button, press the button for the code in block B. (Refer to Table 1.) The operation is completed when the button is released and the LEARNED/TX LED lights. 5 To continue registering other components, repeat steps 2 to 4. • This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown on Table 1. 16