Denon AVR-2802 Owners Manual - Page 18

ENGLISH Learning function • If your AV component is not a DENON product or it cannot be operated with the preset memory codesets, you can "teach" the AVR-2802's remote control to "learn" the codes from the component's original remote control. • The buttons that can be "learned" are the CD, TAPE and CDR/MD system buttons (see page 15) and the DVD, VDP, VCR and TV system buttons (see page 17). (For the CD, CDR/MD, DVD, VDP and TV, the A block buttons can also be "learned", and for the DVD and TV, the B block buttons can also be "learned".) A START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B 4 1 Press the USE/LEARN selector button with the tip of a pen etc., to set the learn mode. Both the START and LEARNED/TX indicators flash. Flashes This unit's remote control unit 2 1,8 VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND RDS MODE PTY MEMORY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI DVD SET UP 3 B 2 Set the program switch to the side to be learned. 5 Check that the START LED is lit, then press the button to be "learned" on the other remote Set to the AUDIO side for the CD, tape deck or control unit. CDR/MD position, to the VIDEO side for the DVD, VDP, VCR or TV position. Other remote AUDIO control unit AVR/AVC VIDEO 3 Set the program switch to the position to be learned. TAPE CDR/MD CD MULTI This unit's remote control unit DVD TV VDP VCR 6 Once the START LED turns off and the LEARNED/TX LED lights, release the button on 4 Set the remote control units so they are facing each other, then press the button to be learned the other remote control unit. on this unit's remote control unit. Transmitting windows Other remote control unit The two LEDs start flashing again. Light 18 Light This unit's remote control unit Approx. 5 cm 7 8 The indicator stops flashing and the START LED lights. The learnable buttons are the buttons which can be operated with the DENON system codes for the CD player, tape deck, CD recorder, MD recorder, the buttons which can be operated with the preset memory for the DVD, VCR, VDP and TV. For the TV only, however, the buttons in the section indicated "A" on the diagram above can also be "learned". Use these to "learn" TV channels. To "learn" other buttons, repeat steps 2 to 6. Once the learning operation is completed, press the USE/LEARN selector button again. The two LEDs stop flashing and the learning mode is cancelled. Check that the stored codes work properly. NOTES: • Up to 26 codes can be "learned", but this number may be lower if the codes are long. • If a non-learnable button is pressed or two or more buttons are pressed at once, the two LEDs will once again light when the button(s) is released. • If the codes could not be stored, the LEARNED/TX LED does not light after the START LED turns off. For limited number of models, codes cannot be stored in RC-904. • If the two LEDs start flashing rapidly after the START LED lights, this means that the memory is already full, and the code you have just attempted to store was not stored. To "learn" that code, first perform the resetting operation. (See page 19.) System call function • The included remote control unit is equipped with a system call function for transmitting multiple remote control signals when a single button is pressed (this is often referred to as a "macro" function). This function can be used to turn on the amplifier's power, select the input source, turn on the monitor TV's power, turn on a source component's power and start playback, etc., all at the touch of a button. (1) System call buttons The buttons that can be used for the system call function are shown on the table below. A series of up to 10 operations can be performed with the POWER ON and OFF buttons, and a series of up to 5 operations can be performed with other buttons. System call signals are already preset at the buttons indicated in the shaded section. System call signals can also be stored at any button on the remote control unit, including the buttons in this section. (See page 19.) Button POWER OFF No. Stored transmissions operation 1 10 Stored operation 2 Stored operation 3 Stored operation 4 Stored operation 5 Stored operation 6 Stored operation 7 Stored operation 8 Stored Stored operation 9 operation 10 POWER ON DVD VDP TV/DBS VCR-1 CD 10 5 Receiver power on DVD player (DVD) power on Receiver input source switched to DVD TV power on DVD player (DVD) playback 5 Receiver power on LD player (VDP) power on Receiver input source switched to VDP TV power on LD player (VDP) playback The system call signals for the POWER Receiver 5 Receiver power on TV power on input source switched to OFF and POWER ON buttons are transmitted from the remote control unit TV/DBS approximately once every second. Receiver 5 Receiver power on Video (VCR) power on input source switched to TV power on Video (VCR) playback The signals for the other buttons (DVD, VCR-1 VDP, TV / DBS, VCR-1 and CD) are Receiver 5 Receiver power on input source switched to CD transmitted approximately once every 1.5 seconds. (2) Using the system call function 1 CALL Press the system call button. • The LEARNED/TX LED flashes for 5 seconds. 2 Press the button at which the desired system call signals are stored while the LEARNED/TX LED is flashing. • The preset signals or the signals you have stored at that button are transmitted in succession. 2 START SYSTEM CALL SET CALL DVD VDP 1 2 TV/DBS 4 5 VCR-1 CD 7 8 VCR-2/V.AUX +10 0 RC-904 LEARNED/TX POWER OFF ON / SOURCE TUNER 3 SHIFT PHONO 6 CDR / TAPE 9 CHANNEL TV/VCR A / B 1 VOLUME DISC SKIP+ SPEAKER DOLBY / DTS SURROUND DIRECT DSP SIMULATION 5CH / 6CH STEREO INPUT MODE ANALOG STEREO EXT.IN MASTER VOL. AUDIO TAPE CDR/MD CD MULTI MUTING AVR/AVC VIDEO TUNING DVD TV VDP VCR SYSTEM SETUP SURROUND PARAMETER BAND MODE MEMORY RDS PTY RT TITLE MENU/GUIDE CH SELECT ENTER SELECT STATUS ON SCREEN DISPLAY RETURN USE/LEARN T.TONE MULTI SET UP