LiftMaster HDSL24UL Installation Manual - English - Page 27

LiftMaster Internet Gateway (not provided), CAPXL Connected Access Portal, To Program the CAPXL

Get LiftMaster HDSL24UL PDF manuals and user guides View all LiftMaster HDSL24UL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

PROGRAMMING LiftMaster Internet Gateway (not provided) To program the operator to the LiftMaster Internet Gateway: 1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router. 2. Connect power to the LiftMaster Internet Gateway. 3. Download the myQ® App. 4. Set up an account and follow the app instructions to add your gate operator. 5. The LiftMaster Internet Gateway will pair to the operator if it is within range and the operator will beep if programming is successful. The gate operator can then be controlled through the myQ® App. 3. Press LEARN button on gate operator - Press and release the LEARN button on the primary operator. The green XMITTER LED will light. NOTE: The operator will time out of programming mode after 180 seconds. CAPXL Connected Access Portal The CAPXL can communicate wirelessly to LiftMaster® UL325 2016 gate operators to send open commands, monitor gate position, and send email notifications if an error occurs in the operator (email notifications are configured in myQ® Business™). Up to 8 gate operators can be paired with the CAPXL - one for each primary and auxiliary relay. If using dual gates, program the CAPXL to the primary operator. 4. Press LEARN button on gate operator again - Press and release the LEARN button again on the primary operator. The yellow NETWORK LED will light. To Program the CAPXL: 1. Enter Admin Mode - Flip dipswitch #1 to the ON position to enter Admin Mode. NOTE: For new installations press the login button without entering information in the Admin Username and Admin Password fields. CAPXL ON ON 5. Select LEARN on display - Select the LEARN button on the display and the Learn button will go from blue to red. The gate operator and the CAPXL will beep once and the NETWORK LED on the gate operator will turn off indicating programming is successful. NOTE: 4 beeps/blinks indicate you are not programming to the primary operator. Reattempt programming from the other operator. 2. Select Outputs and Relay - Select the Outputs tab. Then select the desired relay on the left-hand side (1 through 4). 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
27
LiftMaster Internet Gateway
(not provided)
To program the operator to the LiftMaster Internet Gateway:
1.
Connect the ethernet cable to the LiftMaster Internet Gateway and the
router.
2.
Connect power to the LiftMaster Internet Gateway.
3.
Download the myQ
®
App.
4.
Set up an account and follow the app instructions to add your gate
operator.
5.
The LiftMaster Internet Gateway will pair to the operator if it is within
range and the operator will beep if programming is successful.
The gate operator can then be controlled through the myQ
®
App.
CAPXL Connected Access Portal
The CAPXL can communicate wirelessly to LiftMaster
®
UL325 2016 gate
operators to send open commands, monitor gate position, and send email
notifications if an error occurs in the operator (email notifications are
configured in myQ
®
Business™). Up to 8 gate operators can be paired with
the CAPXL - one for each primary and auxiliary relay. If using dual gates,
program the CAPXL to the primary operator.
To Program the CAPXL:
1.
Enter Admin Mode - Flip dipswitch #1 to the ON position to enter
Admin Mode.
NOTE:
For new installations press the login button
without entering information in the Admin Username and Admin
Password fields.
CAPXL
ON
2.
Select Outputs and Relay - Select the Outputs tab. Then select the
desired relay on the left-hand side (1 through 4).
3.
Press LEARN button on gate operator - Press and release the LEARN
button on the primary operator. The green XMITTER LED will light.
NOTE:
The operator will time out of programming mode after 180
seconds.
4.
Press LEARN button on gate operator again - Press and release the
LEARN button again on the primary operator. The yellow NETWORK
LED will light.
5.
Select LEARN on display - Select the LEARN button on the display and
the Learn button will go from blue to red. The gate operator and the
CAPXL will beep once and the NETWORK LED on the gate operator
will turn off indicating programming is successful.
NOTE:
4
beeps/blinks indicate you are not programming to the primary
operator. Reattempt programming from the other operator.
PROGRAMMING