Kenwood TS-570D User Manual - Page 83

Function APPENDIX ● FW FILTER WIDTH KS KEYER SPEED Sets or reads filter bandwidth. Parameter Format Parameter function 1 2 3 4 5 67 8 FW P1 ; 1 2 3 4 5 67 8 FW ; 1 2 3 4 5 67 8 FW P1 ; 9 10 11 12 13 14 9 10 11 12 13 14 9 10 11 12 13 14 P1 38 FILTER WIDTH Note: CW SSB/AM/FM 0000~0079: 50 Hz 0000: Narrow 0080~0099: 80 Hz 0001~: Wide 0100~0149: 100 Hz 0150~0199: 150 Hz FSK 0200~0299: 200 Hz 0000~0499: 250 Hz 0300~0399: 300 Hz 0500~0999: 500 Hz 0400~0499: 400 Hz 1000~1499: 1000 Hz 0500~0599: 500 Hz 1500~ : 1500 Hz 0600~0999: 600 Hz 1000~1999: 1000 Hz 2000~ : 2000 Hz Input Read Set Function Sets or reads keying speed while using the KY command. Parameter Format Parameter function P1 42 KEYER SPEED 1 2 3 4 5 6 7 8 9 10 11 12 13 14 K S P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 KS ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 K S P1 ; Input Read Set Output Answer Output Answer Function Input Read Set GT AUTO GAIN CONTROL TIME CONSTANT KY CW KEYING Sets or reads AGC time constant. Parameter Format Parameter function P1 39 AGC TIME CONSTANT Note: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 When in FM mode, the transceiver returns " ". G T P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 GT ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 G T P1 ; ID IDENTIFICATION Reads Model number of the transceiver. Parameter Format Parameter function P1 16 MODEL NUMBER Output Answer Input Set Function Converts input characters into Morse code. Parameter Format Parameter function P1 43 KEYER MESSAGE P2 44 KEYER BUFFER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 KY P1 15 16 17 18 19 20 21 22 23 24 25 26 27 28 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 KY ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 K Y P2 ; 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Note: The Set command requires a " " (ASCII code 20h) in the third byte position. Insert " " for bytes that have no characters to make a 28-byte fixed length command. The " " bytes will not send any character. Supported characters include: Letters, numbers Up to 24 characters can be converted as one sentence at one time. The subsequent sentence must be keyed after the current conversion is completed. Read 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Output Answer Function Input Read Set Output Answer Function Input Read Set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LK FREQUENCY LOCK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ID; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 I D P1 ; IF INFORMATION Reads status of the transceiver. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 2 3 4 5 6 7 8 9 10 11 12 13 14 IF; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 IF P1 15 16 17 18 19 20 21 22 23 24 25 26 27 28 P3 P4 P5 P7 29 30 31 32 33 34 35 36 37 38 39 40 41 42 P8 P9 P10 P11 P12 P13 P14 ; Parameter Format Parameter function P1 4 FREQUENCY P2 - NOT USED P3 5 RIT/XIT FREQUENCY P4 1 RIT OFF/ON P5 1 XIT OFF/ON P6 - NOT USED P7 7 MEMORY CHANNEL P8 11 TX/RX P9 2 MODE P10 3 FUNCTION P11 1 SCAN OFF/ON P12 1 SPLIT OFF/ON P13 1 TONE OFF/ON P14 14 TONE NUMBER P15 - NOT USED IS IF SHIFT Output Answer Input Read Set Function Output Answer Input Read Set Function Sets Frequency Lock OFF/ON or reads status. Parameter Format Parameter function P1 1 LOCK OFF/ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L K P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LK ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L K P1 ; LM LOAD MESSAGE DRU or CW message recording Parameter Format Parameter function P1 45 LOAD MESSAGE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L M P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 LM ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 L M P1 ; Sets or reads IF shift. Parameter Format Parameter function P1 40 IF SHIFT DIRECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 I S P1 P2 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 P2 41 IF SHIFT FREQUENCY Note: If P2 is positive or zero, P1 can be "+" or " ". I S; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 I S P1 P2 ; 77 Output Answer Function Input Read Set Output Answer