Kenwood TS-570D User Manual - Page 79
Parameter Table
View all Kenwood TS-570D manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 79 highlights
■ Parameter Table Format No. Name No. of Digits Format 1 SW 1 0: OFF 1: ON 0: No selection 5: AM 1: LSB 6: FSK 2 MODE 1 2: USB 7: CW-R 3: CW 8: No selection 4: FM 9: FSK-R 0: VFO A 3 FUNCTION 1 1: VFO B 2: Memory Represented in Hz. 4 FREQUENCY 11 Ex.: 00014230000 is 14.230 MHz The first digit is "+" or "-", 5 RIT/XIT FREQUENCY 5 and the remaining four digits indicate the frequency in Hz. Ex.: +5320 is +5.32 kHz 7 MEMORY CHANNEL 2 Represented using 00~99. MEMORY 0: Receive (Start freq.) 9 CHANNEL 1 1: Transmit (End freq.) SPLIT DATA (Start/End freq.: Ch.90~99) 10 MEMORY LOCKOUT 1 0: Not locked out 1: Locked out 11 TX/RX 1 0: Receive 1: Transmit 14 TONE NUMBER Represents the tone number 2 (01~39). See the subtone frequency table on page 25. Represents the type of 16 MODEL NUMBER 3 transceiver. TS-570S: 018 TS-570D: 017 22 METER VALUE RM command: 0000~0008 4 SM command: 0000~0015 Relative values are output. 0: No selection 24 METER SWITCH 1 1: SWR 2: COMP 3: ALC 0: No playback A Set command cancels 27 PLAYBACK CHANNEL 1 playback. 1: Channel 1 2: Channel 2 3: Channel 3 30 ANTENNA TUNER 1 0: Antenna tuner thru 1: Antenna tuner in-line Represented using 31 GAIN 3 000 (min.)~255 (max.). MG command: 000~100 0: AI OFF 1: IF command outputs its Answer command 32 AI NUMBER 1 periodically. 2: For parameter changes, the corresponding Answer command is output. 3: Both 1 and 2. 33 ANTENNA NUMBER 1 1: ANT 1 2: ANT 2 APPENDIX ● Format No. Name No. of Digits Format 35 MENU NUMBER 3 Represented using 000~051. 36 MENU SELECTION 4 See table on page 74. 38 FILTER WIDTH 4 Represented using 0000~9999. 39 AGC TIME CONSTANT 3 002: Fast 004: Slow 40 IF SHIFT DIRECTION 1 "+": Upward freq. shift (or " ") "-": Downward freq. shift 41 IF SHIFT FREQUENCY 4 Represented in Hz using 0000~1100. 42 KEYER SPEED Represented in words per 3 minute using 010 (min.)~ 060 (max.). 43 KEYER MESSAGE 24 Contains the CW message. 44 KEYER BUFFER 1 0: Buffer space available 1: Buffer space not available 0: Not recording. A Set command cancels 45 LOAD MESSAGE 1 recording. 1: Channel 1 2: Channel 2 3: Channel 3 46 LEVEL 3 Represented using 000 (min.)~255 (max.). 47 POWER CONTROL 3 Represented in watts using 005~100, 5 W steps. 49 SEMI BREAK-IN DELAY TIME 4 Represented in msec using 0000~1000, 50 ms steps. 1: Partial Reset 50 SYSTEM RESET 1 ([A/B]+[ ]) 2: Full Reset ([A=B]+[ ]) 51 VOX DELAY TIME 4 Represented in msec using 0000~3000. 52 CW RX PITCH Represented using 2 00 (400 Hz min.) ~ 12 (1000 Hz max.). Represented using 00~20 High cut-off 53 DSP SLOPE 2 00: 5.0 kHz 20: 1.0 kHz Low cut-off 00: 10 Hz 20: 1000 Hz 54 VOX GAIN 3 Represented using 001 (min.) ~ 009 (max.). 55 VOICE RECALL 1 1: Voice 1 2: Voice 2 56 NOISE REDUCTION 1 0: Noise Reduction OFF 1: Noise Reduction 1 2: Noise Reduction 2 0: Beat Cancel OFF 57 BEAT CANCEL 1 1: Beat Cancel ON 2: Enhanced Beat Cancel ON 73