Invacare XLT Owners Manual - Page 34

Adjusting Hand Crank

Get Invacare XLT PDF manuals and user guides View all Invacare XLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

SECTION 6-RIDING POSITION Adjusting Hand Crank ƽ WARNING DO NOT operate the handcycle if the hand crank obstructs your view. If the hand crank obstructs your view, adjust the height before using the handcycle - otherwise injury or damage may occur. Adjusting Hand Crank Height - All Models Except Top End XLT Gold NOTE: For this procedure, refer to FIGURE 6.4. 1. Loosen, but DO NOT remove the two set screws securing the hand crank to the fork stem. Hand Crank 2. Move the hand crank assembly up or down on the fork stem until you are comfortable with the position for operational purposes. Set Screws NOTE: The hand crank should be positioned so that when the hand is toward the front of the handcycle, the arm is slightly bent. The arm should NEVER be fully extended (locked) at any point while cranking. Fork Stem FIGURE 6.4 Adjusting Hand Crank Height All Models Except Top End XLT Gold 3. Tighten the hex nut to secure the hand crank in the desired position. 4. Tighten the chain if necessary. Refer to Adjusting Twenty‐Seven Speed Cassette Chain on page 56. Recumbent Handcycle Series 34 Part No 1114850

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
SECTION 6—RIDING POSITION
Recumbent Handcycle Series
34
Part No 1114850
Adjusting Hand Crank
±
WARNING
DO NOT operate the handcycle if the hand crank obstructs your view. If the hand
crank obstructs your view, adjust the height before using the handcycle - otherwise
injury or damage may occur.
Adjusting Hand Crank Height - All Models Except Top End XLT Gold
NOTE: For this procedure, refer to FIGURE 6.4.
1.
Loosen, but DO NOT remove the two
set screws securing the hand crank to
the fork stem.
2.
Move the hand crank assembly up or
down on the fork stem until you are
comfortable with the position for
operational purposes.
NOTE: The hand crank should be positioned so
that when the hand is toward the front of the
handcycle, the arm is slightly bent. The arm
should NEVER be fully extended (locked) at
any point while cranking.
FIGURE 6.4
Adjusting Hand Crank Height -
All Models Except Top End XLT Gold
3.
Tighten the hex nut to secure the hand crank in the desired position.
4.
Tighten the chain if necessary. Refer to Adjusting Twenty
‐
Seven Speed Cassette Chain
on page 56.
Set Screws
Fork Stem
Hand Crank