2010 Yamaha Motorsports RS Vector GT Owners Manual - Page 72

2010 Yamaha Motorsports RS Vector GT Manual

Get 2010 Yamaha Motorsports RS Vector GT PDF manuals and user guides View all 2010 Yamaha Motorsports RS Vector GT manuals

Page 72 highlights

Periodic maintenance and adjustment Shifted to left If the slide runners reach the wear limit, they should be replaced. 1. 2. 3. 4. 5. Forward Gap Slide runner Drive track Slide metal 1. Slide runner 2. Wear limit height 5. Adjust the drive track deflection to specification. NOTICE: The right and left adjusting bolts should be turned an equal amount. [ECS00970] Drive track deflection More than specified Turn in Turn in Less than specified Turn out Turn out Slide runner wear limit height: 10.5 mm (0.41 in) ECS00350 NOTICE Ride on fresh snow frequently. Operating on ice or hard-packed snow will rapidly wear the slide runners. ESU12195 Left adjusting bolt Right adjusting bolt Lubrication Lubricate the following points with the specified grease. EWS00511 6. Tighten the locknuts to their specified torque. Locknut tightening torque: 59 Nm (5.9 m·kgf, 43 ft·lbf) WARNING Do not grease the throttle cable because it could become frozen, which could cause loss of control. Apply a dab of grease onto the cable end only. Lubricants: Brake lever: Silicone grease Other lubrication points: Low-temperature grease 7. 8. 9. Recheck alignment and deflection. If necessary, repeat steps 3 to 6 until the proper adjustment is achieved. Lower the snowmobile to the ground. Tighten the rear axle nut. Rear axle nut tightening torque: 75 Nm (7.5 m·kgf, 54 ft·lbf) Slide runners Check the slide runners for wear and damage. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance and adjustment
66
Shifted to left
5.
Adjust the drive track deflection to speci-
fication.
NOTICE:
The right and left ad-
justing bolts should be turned an
equal amount.
[ECS00970]
6.
Tighten the locknuts to their specified
torque.
7.
Recheck alignment and deflection. If nec-
essary, repeat steps 3 to 6 until the prop-
er adjustment is achieved.
8.
Lower the snowmobile to the ground.
9.
Tighten the rear axle nut.
Slide runners
Check the slide runners for wear and dam-
age.
If the slide runners reach the wear limit, they
should be replaced.
NOTICE
ECS00350
Ride on fresh snow frequently. Operating
on ice or hard-packed snow will rapidly
wear the slide runners.
ESU12195
Lubrication
Lubricate the following points with the speci-
fied grease.
WARNING
EWS00511
Do not grease the throttle cable because it
could become frozen, which could cause
loss of control. Apply a dab of grease onto
the cable end only.
1. Forward
2. Gap
3.
Slide runner
4.
Drive track
5.
Slide metal
Drive track
deflection
More than
specified
Less than
specified
Left adjusting
bolt
Turn in
Turn out
Right adjust-
ing bolt
Turn in
Turn out
Locknut tightening torque:
59 Nm (5.9 m·kgf, 43 ft·lbf)
Rear axle nut tightening torque:
75 Nm (7.5 m·kgf, 54 ft·lbf)
1.
Slide runner
2.
Wear limit height
Slide runner wear limit height:
10.5 mm (0.41 in)
Lubricants:
Brake lever:
Silicone grease
Other lubrication points:
Low-temperature grease