2010 Yamaha Motorsports RS Vector GT Owners Manual - Page 19

2010 Yamaha Motorsports RS Vector GT Manual

Get 2010 Yamaha Motorsports RS Vector GT PDF manuals and user guides View all 2010 Yamaha Motorsports RS Vector GT manuals

Page 19 highlights

Control functions been reached), the tripmeter must be reset after the oil change for the next periodic oil change to be indicated at the correct time. In that case, reset the oil change tripmeter as follows. 1. Push the "SELECT" button until "ODO" is displayed, then push the "RESET" button for approximately 1 second. The distance traveled since the last oil change and "OIL" will flash alternately in the odometer display. 2. Push the "RESET" button for approximately 3 seconds. "00000" and "OIL" will flash alternately in the odometer display 3 times, and then the display will return to the previous display mode. TIP The clock must be set again when the battery is disconnected. Display brightness control This function allows you to adjust the brightness of the meter unit display to suit the outdoor lighting conditions. 1 1. Display brightness level Clock 1 F E 1. Clock To set the clock 1. Turn the main switch to the on position. 2. Push the "SELECT" button and "RESET" button simultaneously until the hour digits start flashing. 3. Push the "RESET" button to change the hour setting, and then push the "SELECT" button. The minute digits will start flashing. 4. Push the "RESET" button to change the minute setting, and then push the "SELECT" button. The clock starts when the "SELECT" button is released. To adjust the display brightness 1. Turn the main switch to the off position. 2. Push and hold down the "SELECT" button. 3. Turn the main switch to the on position, and then, after 5 seconds, release the "SELECT" button. 4. Push the "RESET" button to select the desired display brightness level, and then push the "SELECT" button. The display returns to the previous display mode. ESU10410 High beam indicator light " " The high beam indicator light comes on when the high beams of the headlights are switched on. (See page 17 for headlight beam switch operation.) 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Control functions
13
been reached), the tripmeter must be reset af-
ter the oil change for the next periodic oil
change to be indicated at the correct time.
In that case, reset the oil change tripmeter as
follows.
1.
Push the “SELECT” button until “ODO” is
displayed, then push the “RESET” button
for approximately 1 second. The distance
traveled since the last oil change and
“OIL” will flash alternately in the odometer
display.
2.
Push the “RESET” button for approxi-
mately 3 seconds. “00000” and “OIL” will
flash alternately in the odometer display 3
times, and then the display will return to
the previous display mode.
Clock
To set the clock
1.
Turn the main switch to the on position.
2.
Push the “SELECT” button and “RESET”
button simultaneously until the hour digits
start flashing.
3.
Push the “RESET” button to change the
hour setting, and then push the “SE-
LECT” button. The minute digits will start
flashing.
4.
Push the “RESET” button to change the
minute setting, and then push the “SE-
LECT” button. The clock starts when the
“SELECT” button is released.
TIP
The clock must be set again when the battery
is disconnected.
Display brightness control
This function allows you to adjust the bright-
ness of the meter unit display to suit the out-
door lighting conditions.
To adjust the display brightness
1.
Turn the main switch to the off position.
2.
Push and hold down the “SELECT” but-
ton.
3.
Turn the main switch to the on position,
and then, after 5 seconds, release the
“SELECT” button.
4.
Push the “RESET” button to select the
desired display brightness level, and then
push the “SELECT” button. The display
returns to the previous display mode.
ESU10410
High beam indicator light “
”
The high beam indicator light comes on when
the high beams of the headlights are switched
on. (See page 17 for headlight beam switch
operation.)
1. Clock
F
E
1
1.
Display brightness level
1