2010 Yamaha Motorsports RS Vector GT Owners Manual - Page 27

2010 Yamaha Motorsports RS Vector GT Manual

Get 2010 Yamaha Motorsports RS Vector GT PDF manuals and user guides View all 2010 Yamaha Motorsports RS Vector GT manuals

Page 27 highlights

Control functions ESU13312 Drive guard EWS00401 2. WARNING G Lift up the rear of the drive guard as shown, and then pull the guard rearward to remove it. G Coming in contact with the rotating Vbelt or clutch parts can cause severe injury or death. Never run the engine with the drive guard removed. Make sure that the drive guard is tightened securely before operating the snowmobile to protect against severe injury or death from a broken V-belt or other part should it come off the snowmobile while it is in operation. ECS00930 NOTICE G G Never run the engine with the V-belt removed. Clutch components can be damaged. Be careful not to scratch the windshield when removing or installing the drive guard. To install the drive guard 1. Fit the front slots in the drive guard over the projections on the drive guard front holder. 1 The drive guard is designed to protect the Vbelt clutch and V-belt in case parts break or come loose. The drive guard is located behind the left side cover. (See page 42 for removal procedures.) To remove the drive guard 1. Pull out the drive guard locking pin from the drive guard rear holder. 1. Drive guard 2. 2 Align the slots in the rear of the drive guard with the projections on the drive guard rear holder, and then insert the drive guard locking pin into the holder as shown. 1 1. Drive guard 2. Drive guard locking pin 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Control functions
21
ESU13312
Drive guard
WARNING
EWS00401
●
Coming in contact with the rotating V-
belt or clutch parts can cause severe in-
jury or death. Never run the engine with
the drive guard removed.
●
Make sure that the drive guard is tight-
ened securely before operating the
snowmobile to protect against severe
injury or death from a broken V-belt or
other part should it come off the snow-
mobile while it is in operation.
NOTICE
ECS00930
●
Never run the engine with the V-belt re-
moved. Clutch components can be dam-
aged.
●
Be careful not to scratch the windshield
when removing or installing the drive
guard.
The drive guard is designed to protect the V-
belt clutch and V-belt in case parts break or
come loose.
The drive guard is located behind the left side
cover. (See page 42 for removal procedures.)
To remove the drive guard
1.
Pull out the drive guard locking pin from
the drive guard rear holder.
2.
Lift up the rear of the drive guard as
shown, and then pull the guard rearward
to remove it.
To install the drive guard
1.
Fit the front slots in the drive guard over
the projections on the drive guard front
holder.
2.
Align the slots in the rear of the drive
guard with the projections on the drive
guard rear holder, and then insert the
drive guard locking pin into the holder as
shown.
1.
Drive guard
2.
Drive guard locking pin
2
1
1.
Drive guard
1