2010 Yamaha Motorsports RS Vector GT Owners Manual - Page 53

2010 Yamaha Motorsports RS Vector GT Manual

Get 2010 Yamaha Motorsports RS Vector GT PDF manuals and user guides View all 2010 Yamaha Motorsports RS Vector GT manuals

Page 53 highlights

Periodic maintenance and adjustment 9. Fit the weatherstrip on the headlight unit into the recess in the top of the air filter case cover. 1 1. Weatherstrip Check the T.O.R.S. for proper operation. 1. Start the engine. TIP Refer to the "Starting the engine" section on page 30. 2. Hold the pivot point of the throttle lever away from the throttle switch by putting your thumb (above) and forefinger (below) between the throttle lever pivot and the engine stop switch housing. While holding the pivot point as described above, squeeze the throttle lever gradually. 10. Install the headlight unit bolts, and then tighten them to the specified torque. Tightening torque: Headlight unit bolt: 3 Nm (0.3 m·kgf, 2.2 ft·lbf) 11. Install the top cover, the left and right side covers, and the shroud. ESU11863 Checking the throttle override system (T.O.R.S.) EWS00352 WARNING When checking the T.O.R.S., take precautions to avoid snowmobile movement which could cause an accident: G Make sure that the throttle lever moves smoothly with the engine off before checking the T.O.R.S. G Make sure that the parking brake is applied. G Do not rev the engine to the point that the clutch engages. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
Periodic maintenance and adjustment
47
9.
Fit the weatherstrip on the headlight unit
into the recess in the top of the air filter
case cover.
10. Install the headlight unit bolts, and then
tighten them to the specified torque.
11.
Install the top cover, the left and right side
covers, and the shroud.
ESU11863
Checking the throttle override
system (T.O.R.S.)
WARNING
EWS00352
When checking the T.O.R.S., take precau-
tions to avoid snowmobile movement
which could cause an accident:
●
Make sure that the throttle lever moves
smoothly with the engine off before
checking the T.O.R.S.
●
Make sure that the parking brake is ap-
plied.
●
Do not rev the engine to the point that
the clutch engages.
Check the T.O.R.S. for proper operation.
1.
Start the engine.
TIP
Refer to the “Starting the engine” section on
page 30.
2.
Hold the pivot point of the throttle lever
away from the throttle switch by putting
your thumb (above) and forefinger (be-
low) between the throttle lever pivot and
the engine stop switch housing.
While holding the pivot point as described
above, squeeze the throttle lever gradu-
ally.
1. Weatherstrip
Tightening torque:
Headlight unit bolt:
3 Nm (0.3 m·kgf, 2.2 ft·lbf)
1