Invacare M94 Owners Manual - Page 65

Shroud/wheels

Get Invacare M94 PDF manuals and user guides View all Invacare M94 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

SECTION 10-SHROUD/WHEELS SECTION 10-SHROUD/WHEELS ƽ WARNING After ANY adjustments, repair or service and before use, make sure that all attaching hardware is tightened securely - otherwise injury or damage may result. Before performing any maintenance, adjustment or service verify that On/Off switch on the joystick is in the Off position. Replacing the Flat Free Tires on the Wheel Rim ƽ WARNING DO NOT attempt to replace flat free tires. This procedure MUST be performed by a qualified technician. NOTE: During initial use of the wheelchair, the user may experience flat spots on the wheels. Flat spots will vanish with continued use of the wheelchair. Removing/Installing the Shrouds NOTE: For this procedure, refer to FIGURE 10.1 on page 66. Removing 1. Remove the seat. Refer to Removing/Installing the Seat Assembly on page 50. 2. Perform one of the following: • Top Shroud ‐ Lift up on rear edge of top shroud to release the four hook and loop strips that secure the top shroud to the base frame as shown in Detail "A" of FIGURE 10.1. • Front Shroud ‐ Turn release knob ¼‐turn to the unlocked position and lift up to remove front shroud from base frame hooks as shown in Detail "B" in FIGURE 10.1. Installing 1. Perform one of the following: • Top Shroud ‐ Position top shroud on to the base frame and gently press down on top shroud to secure the four hook and loop strips that secure the top shroud to the base frame as shown in Detail "A" of FIGURE 10.1. • Front Shroud ‐ Position front shroud onto the two base frame hooks. Turn release knob ¼‐turn to the locked position as shown in Detail "B" of FIGURE 10.1. 2. Install the seat assembly. Refer to Removing/Installing the Seat Assembly on page 50. Part No 1122145 65 Pronto® M94™

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 10—SHROUD/WHEELS
Part No 1122145
65
Pronto® M94™
SECTION 10—SHROUD/WHEELS
±
WARNING
After ANY adjustments, repair or service and before use, make sure that all
attaching hardware is tightened securely - otherwise injury or damage may result.
Before performing any maintenance, adjustment or service verify that On/Off
switch on the joystick is in the Off position.
Replacing the Flat Free Tires on the Wheel Rim
±
WARNING
DO NOT attempt to replace flat free tires. This procedure MUST be performed by
a qualified technician.
NOTE: During initial use of the wheelchair, the user may experience flat spots on the wheels. Flat
spots will vanish with continued use of the wheelchair.
Removing/Installing the Shrouds
NOTE: For this procedure, refer to FIGURE 10.1 on page 66.
Removing
1.
Remove the seat. Refer to Removing/Installing the Seat Assembly
on page 50.
2.
Perform one of the following:
•
Top Shroud
‐
Lift up on rear edge of top shroud to release the four hook and loop
strips that secure the top shroud to the base frame as shown in Detail “A” of
FIGURE 10.1.
•
Front Shroud
‐
Turn release knob ¼
‐
turn to the unlocked position and lift up to
remove front shroud from base frame hooks as shown in Detail “B” in
FIGURE 10.1.
Installing
1.
Perform one of the following:
•
Top Shroud
‐
Position top shroud on to the base frame and gently press down on
top shroud to secure the four hook and loop strips that secure the top shroud to the
base frame as shown in Detail “A” of FIGURE 10.1.
•
Front Shroud
‐
Position front shroud onto the two base frame hooks. Turn release
knob ¼
‐
turn to the locked position as shown in Detail “B” of FIGURE 10.1.
2.
Install the seat assembly. Refer to Removing/Installing the Seat Assembly
on page 50.