Invacare M94 Owners Manual - Page 31

Using the Joystick to Drive the Wheelchair

Get Invacare M94 PDF manuals and user guides View all Invacare M94 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

SECTION 5-WHEELCHAIR OPERATION Using the Joystick to Drive the Wheelchair NOTE: For this procedure, refer to FIGURE 5.2. The joystick is located on the joystick housing and provides smooth control of speed and direction. It is equipped with 360 degrees of mobility for ease of operation. The joystick is spring‐loaded, and automatically returns to the upright (neutral) position when released. Pushing the joystick in a given direction causes the wheelchair to move in that direction. The joystick has proportional drive control, meaning that the further it is pushed from the upright (neutral) position, the faster the wheelchair moves. The maximum speed, however, is limited by the setting of the speed‐control knob. To slow the wheelchair to a stop, simply release the joystick. The wheelchair has automatic speed and direction compensation to minimize corrections. When first learning to drive, select a slow speed and try to drive the wheelchair as slowly as possible by pushing the joystick slightly forward. This exercise will help you learn to utilize the full potential of the proportional control and allow you to start and stop smoothly. To drive the wheelchair, perform the following: 1. Adjust speed control knob to the appropriate setting. 2. Turn the power On. Refer to Turning the Power On/Off on page 30. 3. Maneuver the joystick in the following manner: MOVEMENT ACTION FORWARD Push joystick forward, towards the front of the wheelchair. REVERSE Pull joystick back, towards the rear of the wheelchair. Turn RIGHT Move joystick toward the right side of the wheelchair. Turn LEFT Move joystick toward the left side of the wheelchair. STOP Release the joystick and the wheelchair will slow to a stop. To Move Left To Move Forward To Move Backward Front of Wheelchair To Move Right Rear of Wheelchair Joystick FIGURE 5.2 Using the Joystick to Drive the Wheelchair NOTE: For specific information about the joystick installed on the wheelchair, refer to one of these procedures: • SPJ+, MK6i SPJ+ w/PSS and MK6i SPJ+ w/ACC Joystick Switches and Indicators on page 32. • MPJ+ Joystick Switches and Indicators on page 34. Part No 1122145 31 Pronto® M94™

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 5—WHEELCHAIR OPERATION
Part No 1122145
31
Pronto® M94™
Using the Joystick to Drive the Wheelchair
NOTE: For this procedure, refer to FIGURE 5.2.
The joystick is located on the joystick housing and provides smooth control of speed and
direction. It is equipped with 360 degrees of mobility for ease of operation. The joystick is
spring
‐
loaded, and automatically returns to the upright (neutral) position when released.
Pushing the joystick in a given direction causes the wheelchair to move in that direction.
The joystick has proportional drive control, meaning that the further it is pushed from the
upright (neutral) position, the faster the wheelchair moves. The maximum speed,
however, is limited by the setting of the speed
‐
control knob.
To slow the wheelchair to a stop, simply release the joystick. The wheelchair has
automatic speed and direction compensation to minimize corrections.
When first learning to drive, select a slow speed and try to drive the wheelchair as slowly
as possible by pushing the joystick slightly forward. This exercise will help you learn to
utilize the full potential of the proportional control and allow you to start and stop
smoothly.
To drive the wheelchair, perform the following:
1.
Adjust speed control knob to the appropriate setting.
2.
Turn the power On. Refer to Turning the Power On/Off
on page 30.
3.
Maneuver the joystick in the following manner:
FIGURE 5.2
Using the Joystick to Drive the
Wheelchair
NOTE: For specific information about the joystick installed on the wheelchair, refer to one of these
procedures:
•
SPJ+, MK6i SPJ+ w/PSS and MK6i SPJ+ w/ACC Joystick Switches and Indicators
on
page 32.
•
MPJ+ Joystick Switches and Indicators
on page 34.
MOVEMENT
ACTION
FORWARD
Push joystick forward, towards
the front of the wheelchair.
REVERSE
Pull joystick back, towards the
rear of the wheelchair.
Turn RIGHT
Move joystick toward the right
side of the wheelchair.
Turn LEFT
Move joystick toward the left side
of the wheelchair.
STOP
Release the joystick and the
wheelchair will slow to a stop.
To Move
Right
To Move
Forward
To Move
Left
To Move
Backward
Joystick
Front of
Wheelchair
Rear of
Wheelchair