Invacare M94 Owners Manual - Page 62

Reinstall the seat. Refer to Removing/Installing the Seat Assembly

Get Invacare M94 PDF manuals and user guides View all Invacare M94 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

SECTION 9-FRONT RIGGINGS NOTE: Telescoping front rigging supports may be extended up to 2‐inches from the wheelchair frame in 1‐inch increments. This adjustment does not affect seat depth. NOTE: When installing the front riggings support tubes, ensure that the hinge pins are on the outside of the chair facing away from the seat frame. NOTE: For this procedure, refer to FIGURE 9.6 on page 63. 1. Remove the seat. Refer to Removing/Installing the Seat Assembly on page 50. 2. Remove the two socket bolts and locknuts that secure telescoping front rigging support to the seat frame. 3. Perform one of the following: • Adjusting i. Align the appropriate mounting hole of the telescoping front rigging support with the front mounting hole in the seat frame tubes to achieve the desired depth as shown in FIGURE 9.6. • Replacing i. Remove the existing telescoping front rigging support from the wheelchair frame. ii. Insert the new telescoping front rigging support into the seat frame. iii. Align the appropriate mounting hole of the telescoping front rigging support with the front mounting hole in the seat frame tubes to achieve the desired depth as shown in FIGURE 9.6. NOTE: The footplate will be on the inside of the wheelchair when locked in place. 4. Using the two socket bolts and locknuts, secure the telescoping front rigging support to the seat frame as shown in FIGURE 9.6. 5. If necessary, repeat STEPS 2‐4 on remaining telescoping front rigging support. 6. Reinstall the seat. Refer to Removing/Installing the Seat Assembly on page 50. Pronto® M94™ 62 Part No 1122145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 9—FRONT RIGGINGS
Pronto® M94™
62
Part No 1122145
NOTE: Telescoping front rigging supports may be extended up to 2
‐
inches from the wheelchair
frame in 1
‐
inch increments. This adjustment does not affect seat depth.
NOTE: When installing the front riggings support tubes, ensure that the hinge pins are on the
outside of the chair facing away from the seat frame.
NOTE: For this procedure, refer to FIGURE 9.6 on page 63.
1.
Remove the seat. Refer to Removing/Installing the Seat Assembly
on page 50.
2.
Remove the two socket bolts and locknuts that secure telescoping front rigging
support to the seat frame.
3.
Perform one of the following:
•
Adjusting
i.
Align the appropriate mounting hole of the telescoping front rigging support
with the front mounting hole in the seat frame tubes to achieve the desired
depth as shown in FIGURE 9.6.
•
Replacing
i.
Remove the existing telescoping front rigging support from the wheelchair
frame.
ii.
Insert the new telescoping front rigging support into the seat frame.
iii. Align the appropriate mounting hole of the telescoping front rigging support
with the front mounting hole in the seat frame tubes to achieve the desired
depth as shown in FIGURE 9.6.
NOTE: The footplate will be on the inside of the wheelchair when locked in place.
4.
Using the two socket bolts and locknuts, secure the telescoping front rigging support
to the seat frame as shown in FIGURE 9.6.
5.
If necessary, repeat STEPS 2
‐
4 on remaining telescoping front rigging support.
6.
Reinstall the seat. Refer to Removing/Installing the Seat Assembly
on page 50.