Invacare M94 Owners Manual - Page 50

Removing/Installing the Seat Assembly

Get Invacare M94 PDF manuals and user guides View all Invacare M94 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

SECTION 7-SEAT Removing/Installing the Seat Assembly ƽ WARNING DO NOT store items under seat - interference with seat latch may result. NOTE: For this procedure, refer to FIGURE 7.4. Removing 1. Disconnect the joystick. Refer to Disconnecting/Connecting the Joysticks on page 42. 2. Push down on the latch bar underneath front of seat. 3. Tilt front edge of seat up. 4. Slide the seat assembly forward to disengage seat from the pivot brackets located in the rear. Installing 1. Position the seat in the rear pivot brackets as shown in FIGURE 7.4. 2. Tilt front edge of seat down. 3. When seat is lowered, engage seat brackets into seat clevis pins. ƽ WARNING When reinstalling the seat verify that the seat brackets are engaged with the seat clevis pins by pulling up on the latch bar. 4. Pull up on latch bar to verify that brackets are engaged with seat clevis pins. 5. Connect the joystick. Refer to Disconnecting/Connecting the Joysticks on page 42. Rear Pivot Brackets Seat Clevis Pins NOTE: Van Seat model shown. ASBA seat removes/ installs in the same way. Latch Bar (located under the front of the seat) FIGURE 7.4 Removing/Installing the Seat Assembly Pronto® M94™ 50 Part No 1122145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
SECTION 7—SEAT
Pronto® M94™
50
Part No 1122145
Removing/Installing the Seat Assembly
±
WARNING
DO NOT store items under seat - interference with seat latch may result.
NOTE: For this procedure, refer to FIGURE 7.4.
Removing
1.
Disconnect the joystick. Refer to Disconnecting/Connecting the Joysticks
on page 42.
2.
Push down on the latch bar underneath front of seat.
3.
Tilt front edge of seat up.
4.
Slide the seat assembly forward to disengage seat from the pivot brackets located in
the rear.
Installing
1.
Position the seat in the rear pivot brackets as shown in FIGURE 7.4.
2.
Tilt front edge of seat down.
3.
When seat is lowered, engage seat brackets into seat clevis pins.
±
WARNING
When reinstalling the seat verify that the seat brackets are engaged with the seat
clevis pins by pulling up on the latch bar.
4.
Pull up on latch bar to verify that brackets are engaged with seat clevis pins.
5.
Connect the joystick. Refer to Disconnecting/Connecting the Joysticks
on page 42.
FIGURE 7.4
Removing/Installing the Seat Assembly
Latch Bar
(located under the
front of the seat)
NOTE: Van Seat model
shown. ASBA seat removes/
installs in the same way.
Rear Pivot
Brackets
Seat Clevis Pins