HP Latex 260 Maintenance and troubleshooting guide - Page 75

The following graphic shows the take-up reel sensors and cable., Take-up reel sensor

Get HP Latex 260 PDF manuals and user guides View all HP Latex 260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Take-up reel LED status Issue Solid red Take-up reel is not winding Print job interrupted? No Solid green Solid green Take-up reel is not No winding Take-up reel is winding No in the wrong direction Possible cause Possible solution There is too much resistance on the takeup reel motor. Ensure that the substrate is not winding too tightly. A loopshaping core should be inserted and hanging as shown in the User's guide. The take-up reel power switch is in the Off position Ensure that the take-up reel power switch is in the On position. The take-up reel winddirection switch is in the wrong winding position. Flip the take-up reel wind-direction switch to the correct position. After 3 seconds, the printer recognizes the problem and interrupts the print job. See the first error listed in this table. The following graphic shows the take-up reel sensors and cable. 1. Take-up reel sensor 2. Take-up reel sensor and cable housing unit ENWW Take-up reel does not wind 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Take-up reel LED status
Issue
Print job interrupted?
Possible cause
Possible solution
Solid red
Take-up reel is not
winding
No
There is too much
resistance on the take-
up reel motor.
Ensure that the
substrate is not winding
too tightly. A loop-
shaping core should be
inserted and hanging as
shown in the
User's
guide
.
Solid green
Take-up reel is not
winding
No
The take-up reel power
switch is in the Off
position
Ensure that the take-up
reel power switch is in
the On position.
Solid green
Take-up reel is winding
in the wrong direction
No
The take-up reel wind-
direction switch is in the
wrong winding position.
After 3 seconds, the
printer recognizes the
problem and interrupts
the print job. See the
first error listed in this
table.
Flip the take-up reel
wind-direction switch to
the correct position.
The following graphic shows the take-up reel sensors and cable.
1.
Take-up reel sensor
2.
Take-up reel sensor and cable housing unit
ENWW
Take-up reel does not wind
69