HP Latex 260 Maintenance and troubleshooting guide - Page 41

Replace the printhead cleaning kit, WARNING

Get HP Latex 260 PDF manuals and user guides View all HP Latex 260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Replace the printhead cleaning kit The printhead cleaning kit contains the printhead cleaning cartridge, the ink funnel and the ink filter. When the front panel prompts you to replace the printhead cleaning kit, you should replace first the printhead cleaning cartridge, then the ink funnel, then the printhead cleaning container and ink filter. NOTE: The printhead cleaning container is not contained in the kit, but should be replaced at the same time. Therefore, make sure that you have a new printhead cleaning container ready, as well as a new printhead cleaning kit. TIP: If you want to remove and inspect the printhead cleaning cartridge at any time, you can start the following procedure. If you put the old printhead cleaning cartridge back into the printer after inspecting it, the procedure ends at that point. 1. On the printer's front panel, select the icon, then select Replace PH cleaning kit. 2. The printhead cleaning cartridge is located in a slot underneath the front panel, at the front of the printer. Open the door. Follow these precautions when removing a printhead cleaning cartridge: ● Be careful not to get ink on your hands. Ink may be on, around and inside the replaced printhead cleaning cartridge. ● Always handle and store the replaced printhead cleaning cartridge upright to avoid spilling any ink. WARNING! Make sure that the printer wheels are locked (the brake lever is pressed down) to prevent the printer from moving. ENWW Replace the printhead cleaning kit 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Replace the printhead cleaning kit
The printhead cleaning kit contains the printhead cleaning cartridge, the ink funnel and the ink filter.
When the front panel prompts you to replace the printhead cleaning kit, you should replace first the
printhead cleaning cartridge, then the ink funnel, then the printhead cleaning container and ink filter.
NOTE:
The printhead cleaning container is not contained in the kit, but should be replaced at the same time.
Therefore, make sure that you have a new printhead cleaning container ready, as well as a new printhead
cleaning kit.
TIP:
If you want to remove and inspect the printhead cleaning cartridge at any time, you can start the
following procedure. If you put the old printhead cleaning cartridge back into the printer after inspecting it,
the procedure ends at that point.
1.
On the printer's front panel, select the
icon, then select
Replace PH cleaning kit
.
2.
The printhead cleaning cartridge is located in a slot underneath the front panel, at the front of the
printer. Open the door.
Follow these precautions when removing a printhead cleaning cartridge:
●
Be careful not to get ink on your hands. Ink may be on, around and inside the replaced printhead
cleaning cartridge.
●
Always handle and store the replaced printhead cleaning cartridge upright to avoid spilling any
ink.
WARNING!
Make sure that the printer wheels are locked (the brake lever is pressed down) to prevent
the printer from moving.
ENWW
Replace the printhead cleaning kit
35