HP Latex 260 Maintenance and troubleshooting guide - Page 20

Reseat, Replace, Close the carriage interconnect wiper, trapping the sponge in place.

Get HP Latex 260 PDF manuals and user guides View all HP Latex 260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Use this to clean the electrical interconnects on both the printhead carriage and the printhead if the Reseat or Replace message persists next to the printhead on the front-panel display. 1. Remove a new pre-moistened replacement sponge from its pouch. A supply of sponges is included in the box with the wiper. If all sponges have been used, more can be obtained by calling your service representative. 2. Open the carriage interconnect wiper. 3. Load the sponge by positioning the sponge on the face of the carriage interconnect wiper with the shorter tab in the locating slot. 4. Close the carriage interconnect wiper, trapping the sponge in place. 5. Open the printhead carriage latch and extract the printhead that is causing the problem, as indicated on the front panel. See Replace a printhead on page 30. 14 Chapter 4 Hardware maintenance ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Use this to clean the electrical interconnects on both the printhead carriage and the printhead if the
Reseat
or
Replace
message persists next to the printhead on the front-panel display.
1.
Remove a new pre-moistened replacement sponge from its pouch.
A supply of sponges is included in the box with the wiper. If all sponges have been used, more can be
obtained by calling your service representative.
2.
Open the carriage interconnect wiper.
3.
Load the sponge by positioning the sponge on the face of the carriage interconnect wiper with the
shorter tab in the locating slot.
4.
Close the carriage interconnect wiper, trapping the sponge in place.
5.
Open the printhead carriage latch and extract the printhead that is causing the problem, as indicated on
the front panel. See
Replace a printhead
on page
30
.
14
Chapter 4
Hardware maintenance
ENWW