HP Latex 260 Maintenance and troubleshooting guide - Page 40

takes up to 18 minutes. If the printer identifies a problem when preparing the printheads, the process

Get HP Latex 260 PDF manuals and user guides View all HP Latex 260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

6. Insert all of the other printheads that need to be installed, and close the carriage cover. 7. Make sure that the end of the latch catches the wire loop on the near side of the carriage. 8. Lower the latch to rest on the carriage cover. When all of the printheads have been inserted correctly and the printer has accepted them, the printer beeps. NOTE: If the printer does not beep when you insert the printhead and the Replace message appears on the front-panel display, you might need to reinsert the printhead. 9. Close and lock the printer window. 10. The front-panel display confirms that all of the printheads are correctly inserted. The printer starts checking and preparing the printheads. The default routine process, when all printheads are changed, takes up to 18 minutes. If the printer identifies a problem when preparing the printheads, the process takes longer, up to 30 minutes. For a single printhead insertion, the time varies between 10 and 20 minutes. After all printheads are checked and prepared, the printhead realignment procedure runs automatically if substrate is loaded. 34 Chapter 4 Hardware maintenance ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
6.
Insert all of the other printheads that need to be installed, and close the carriage cover.
7.
Make sure that the end of the latch catches the wire loop on the near side of the carriage.
8.
Lower the latch to rest on the carriage cover.
When all of the printheads have been inserted correctly and the printer has accepted them, the printer
beeps.
NOTE:
If the printer does not beep when you insert the printhead and the
Replace
message appears
on the front-panel display, you might need to reinsert the printhead.
9.
Close and lock the printer window.
10.
The front-panel display confirms that all of the printheads are correctly inserted. The printer starts
checking and preparing the printheads. The default routine process, when all printheads are changed,
takes up to 18 minutes. If the printer identifies a problem when preparing the printheads, the process
takes longer, up to 30 minutes. For a single printhead insertion, the time varies between 10 and 20
minutes. After all printheads are checked and prepared, the printhead realignment procedure runs
automatically if substrate is loaded.
34
Chapter 4
Hardware maintenance
ENWW