HP Latex 260 Maintenance and troubleshooting guide - Page 7

Safety precautions, General safety guidelines, Electrical shock hazard

Get HP Latex 260 PDF manuals and user guides View all HP Latex 260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

1 Safety precautions Before using your printer, read the following safety precautions to make sure you use the equipment safely. You are expected to have the appropriate technical training and experience necessary to be aware of hazards to which you may be exposed in performing a task, and take appropriate measures to minimize the risks to yourself and to other people. General safety guidelines ● Refer to the installation instructions before connecting the printer to the supply. ● There are no operator-serviceable parts inside the printer except those covered by HP's Customer Self Repair program (see http://www.hp.com/go/selfrepair/). Refer servicing of other parts to qualified service personnel. ● Turn off the printer, unplug both power cords from the power outlets, and call your service representative in any of the following cases. ◦ The power cord or plug is damaged. ◦ Liquid has entered the printer. ◦ There is smoke or an unusual smell coming from the printer. ◦ The printer has been dropped or the drying or curing module damaged. ◦ The printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) has been repeatedly tripped. ◦ The printer is not operating normally. ● Turn off the printer and unplug both power cords from the power outlets in either of the following cases. ◦ During a thunderstorm ◦ During a power failure Electrical shock hazard WARNING! The drying and curing modules operate at hazardous voltages capable of causing death or serious personal injury. The printer uses two power cords. Unplug both power cords before servicing the printer. The printer must be connected to earthed mains outlets only. To avoid the risk of electric shock: ENWW General safety guidelines 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
1
Safety precautions
Before using your printer, read the following safety precautions to make sure you use the equipment safely.
You are expected to have the appropriate technical training and experience necessary to be aware of hazards
to which you may be exposed in performing a task, and take appropriate measures to minimize the risks to
yourself and to other people.
General safety guidelines
●
Refer to the installation instructions before connecting the printer to the supply.
●
There are no operator-serviceable parts inside the printer except those covered by HP's Customer Self
Repair program (see
go/selfrepair/
). Refer servicing of other parts to qualified
service personnel.
●
Turn off the printer, unplug both power cords from the power outlets, and call your service
representative in any of the following cases.
◦
The power cord or plug is damaged.
◦
Liquid has entered the printer.
◦
There is smoke or an unusual smell coming from the printer.
◦
The printer has been dropped or the drying or curing module damaged.
◦
The printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) has been
repeatedly tripped.
◦
The printer is not operating normally.
●
Turn off the printer and unplug both power cords from the power outlets in either of the following
cases.
◦
During a thunderstorm
◦
During a power failure
Electrical shock hazard
WARNING!
The drying and curing modules operate at hazardous voltages capable of causing death or
serious personal injury.
The printer uses two power cords. Unplug both power cords before servicing the printer. The printer must be
connected to earthed mains outlets only.
To avoid the risk of electric shock:
ENWW
General safety guidelines
1