HP Latex 260 Maintenance and troubleshooting guide - Page 69

Troubleshoot substrate issues, The substrate cannot be loaded successfully

Get HP Latex 260 PDF manuals and user guides View all HP Latex 260 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

7 Troubleshoot substrate issues The substrate cannot be loaded successfully Here are some suggestions to try if you cannot load the substrate successfully. ● Reread the loading instructions in the User's guide, and make sure that you are following them. ● When loading a textile substrate, remember to use the loading accessory, and select Load with accessory in the front panel. ● If automatic loading is unsuccessful, try manual loading instead. ● The substrate might be loaded at an angle (skewed or mislocated). Make sure that the right edge of the substrate is aligned with the roll on the input spindle. ● The substrate might be crumpled or warped, or have irregular edges. ● If the substrate jams in the substrate path to the platen, the leading edge of the substrate might not be straight or clean. Remove the initial 2 cm (1 in) of substrate from the roll and try again. This might be necessary even with a new roll of substrate. ● Make sure that the spindle is correctly inserted. ● Make sure that the substrate is correctly loaded on the spindle, and that it loads over the roll towards you. ● Make sure that the substrate is wound tightly. The substrate is mispositioned If you see the above display on the front panel, proceed as follows. 1. Lift the substrate lever. 2. Manually reposition the substrate on the platen. ENWW The substrate cannot be loaded successfully 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
7
Troubleshoot substrate issues
The substrate cannot be loaded successfully
Here are some suggestions to try if you cannot load the substrate successfully.
●
Reread the loading instructions in the
User's guide
, and make sure that you are following them.
●
When loading a textile substrate, remember to use the loading accessory, and select
Load with
accessory
in the front panel.
●
If automatic loading is unsuccessful, try manual loading instead.
●
The substrate might be loaded at an angle (skewed or mislocated). Make sure that the right edge of the
substrate is aligned with the roll on the input spindle.
●
The substrate might be crumpled or warped, or have irregular edges.
●
If the substrate jams in the substrate path to the platen, the leading edge of the substrate might not be
straight or clean. Remove the initial 2 cm (1 in) of substrate from the roll and try again. This might be
necessary even with a new roll of substrate.
●
Make sure that the spindle is correctly inserted.
●
Make sure that the substrate is correctly loaded on the spindle, and that it loads over the roll towards
you.
●
Make sure that the substrate is wound tightly.
The substrate is mispositioned
If you see the above display on the front panel, proceed as follows.
1.
Lift the substrate lever.
2.
Manually reposition the substrate on the platen.
ENWW
The substrate cannot be loaded successfully
63