Home » HP Manuals » Printers » HP Latex 260 » Manual Viewer

HP Latex 260 Maintenance and troubleshooting guide - Page 54

Check the quantity of ink on the substrate, Bidir, Maybe, Start here, Too much ink

$Get HP Latex 260 PDF manuals and user guides$

Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Passes 10 12 Uni/bidir Self adhesive Bidir Yes Bidir Yes Banner Yes Yes 16 Bidir Yes Yes 18* Bidir Yes Yes 20 to 32 Bidir Yes Yes Textile No Start here Yes Yes Yes Film No Maybe Syntheti c paper No Maybe Paper aqueous Yes Yes Paper solvent Yes Yes Start Start Yes Yes here here Yes Yes Yes Yes Yes Yes Yes Yes Low temp. Yes Yes Yes Yes Yes Mesh Yes Yes Yes Yes Yes * Unlike other printmodes, the 18-pass printmode has 1200 dpi x 1200 dpi input data resolution at 1 bpp (1 bit per pixel). Therefore, to generate a 18-pass media preset you should start either from an existing 18-pass preset or from scratch. In the same way, do not clone an 18-pass media preset to generate a preset with a print mode other than 18-pass. Key ● Bidir: bidirectional ● No: not recommended ● Maybe: may be worth trying for extra speed ● Start here, Yes: recommended NOTE: More specific settings for many substrates from different vendors are available in the HP Media Finder at http://www.hp.com/go/latexmediafinder/. Check the quantity of ink on the substrate Check that the ink quantities in your media preset are adequate. Look at the color patches in the HP diagnostic chart and check that the patches have the correct amount of ink using the guidelines below: 1. Too much ink: There are several possible symptoms of this problem. ● The last two or three scales of the chart look the same. 48 Chapter 5 Substrate settings ENWW

Section	Page
Safety precautions	7
General safety guidelines	7
Electrical shock hazard	7
Heat hazard	8
Fire hazard	8
Mechanical hazard	8
Heavy substrate hazard	9
Ink handling	9
Warnings and cautions	9
Warning labels	9
Printer status	11
Check printer status	11
Check the status of the ink system	11
Check the status of the ink cartridges	12
Ink menu procedure	12
Check the status of a printhead	12
Check the file system	13
Printer alerts	13
Firmware update	15
Hardware maintenance	17
Ink system tips	17
Align the printheads	17
Automatic alignment	17
Manual alignment	18
Check substrate porosity	18
Clean the electrical connections on a printhead	19
Clean the exterior of the printer	22
Clean the platen	23
Clean after porous substrates	24
Clean (recover) the printheads	25
Clean the substrate-advance sensor window	25
Clean and lubricate the carriage rail	26
Maintain the ink cartridges	28
Move or store the printer	28
Replace an ink cartridge	29
Refilled and non-HP ink cartridges	32
Replace the ink maintenance kit	33
Replace a printhead	36
Replace the printhead cleaning kit	41
Service maintenance	45
Substrate settings	47
Download media presets	47
Add a new substrate	47
Summary	48
Select printer settings and color profile	48
Load the substrate and print the diagnostic plot	50
Change settings while printing	51
Advanced settings	51
Temperature profile	53
Select the number of passes	53
Check the quantity of ink on the substrate	54
Faster printing	57
Color calibration	57
Color profiles	58
Color reproduction tricks	58
Troubleshoot print-quality issues	59
General printing advice	59
Use the printhead status plot	59
Print the printhead status plot	59
Interpret the printhead status plot	59
Corrective action	60
What to do if problems persist	60
Graininess	60
Horizontal banding	61
Adjust the substrate advance	62
Substrate advance adjustment on the fly	62
Vertical banding	63
The print is deformed into a curved shape	63
Misaligned colors	64
Color intensity varies	64
Lack of sharpness	65
Black areas look hazy	65
Ink smears	65
Subtle stains or uneven appearance	65
The ink smudges when touched, or looks oily	66
The dimensions of the print are wrong	66
Tiling issues	66
Troubleshoot substrate issues	69
The substrate cannot be loaded successfully	69
The substrate is mispositioned	69
The substrate has jammed	70
Check the substrate path	70
Check the printhead path	70
Avoiding substrate jams	71
The substrate is deformed or wrinkled	72
The substrate has shrunk or expanded	72
The substrate has bow deformation	73
The automatic cutter does not work	74
Take-up reel substrate jam	74
Take-up reel does not wind	74
Troubleshoot ink-system issues	77
Ink maintenance kit needs to be installed	77
Cannot insert an ink cartridge	77
Cannot insert a printhead	77
Cannot insert the printhead cleaning cartridge	77
Front panel recommends reseating or replacing a printhead	77
Clean the printheads	78
Align the printheads	78
Reinsert printheads procedure	78
Image Quality Maintenance menu procedure	79
Scan errors during alignment	79
Troubleshoot other issues	81
The printer cannot get an IP address	81
Cannot access the Embedded Web Server	81
The printer is not printing	82
The software program slows down or stalls while generating the print job	82
The printer seems slow	82
Cannot access files on the hard disk	83
Communication failures between computer and printer	83
The platen rollers squeak	83
Front-panel error messages	85
Printer logs	90
When you need help	91
Introduction	91
Documentation	91
Customer Self Repair	91
HP Customer Care Centers	91
Telephone number	92
Service information	92
Summary of common printing problems	93