Epson TM-T20II UB-R04 Technical Reference Guide - Page 40

Change the Setting Using EpsonNet Config (USB Connection)

Get Epson TM-T20II PDF manuals and user guides View all Epson TM-T20II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Change the Setting Using EpsonNet Config (USB Connection) Connect the UB-R04 to the setting computer with the USB connection, and change the setting from EpsonNet Config. This method is similar to the initial setting procedure. It is suited for setting with other networks because the connection with the UB-R04 is not cut. Changing method For the details of the changing method, refer to "Setting Using the USB Connection" on page 26. Confirm after changing After changing of the setting, start up the Web browser of the computer on the network and enter the IP Address of the UB-R04 in the address bar. For the details of the confirming, refer to "Confirm after changing" on page 39. Change the Setting Using EpsonNet Config (By Network) It is suited for changing the setting in the same network. Changing method For the details of the changing method, refer to "Setting Using the Wireless LAN Connection" on page 30. Confirm after changing After changing of the setting, start up the Web browser of the computer on the network and enter the IP Address of the UB-R04 in the address bar. For the details of the confirming, refer to "Confirm after changing" on page 39. • When you initialize or change the printer settings, the printer is reset to reflect the settings. It may take about 1 minute depending on the network settings or environment. Also, your application may indicate power off during the time waiting for reset. In that case, wait for about 1 minute, and then reconnect to the printer. • Where wireless LAN communication is in heavy traffic, your application may falsely recognize that the communication is disconnected and indicate power off due to response delay. In that case, disable Power Save to improve the trouble. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
40
Change the Setting Using EpsonNet Config (USB Connection)
Connect the UB-R04 to the setting computer with the USB connection, and change the setting from
EpsonNet Config.
This method is similar to the initial setting procedure. It is suited for setting with other networks because
the connection with the UB-R04 is not cut.
Changing method
For the details of the changing method, refer to
"Setting Using the USB Connection" on page 26
.
Confirm after changing
After changing of the setting, start up the Web browser of the computer on the network and enter the IP
Address of the UB-R04 in the address bar.
For the details of the confirming, refer to
"Confirm after changing" on page 39
.
Change the Setting Using EpsonNet Config (By Network)
It is suited for changing the setting in the same network.
Changing method
For the details of the changing method, refer to
"Setting Using the Wireless LAN Connection" on page 30
.
Confirm after changing
After changing of the setting, start up the Web browser of the computer on the network and enter the IP
Address of the UB-R04 in the address bar.
For the details of the confirming, refer to
"Confirm after changing" on page 39
.
•
When you initialize or change the printer settings, the printer is reset to reflect the settings. It
may take about 1 minute depending on the network settings or environment. Also, your
application may indicate power off during the time waiting for reset. In that case, wait for
about 1 minute, and then reconnect to the printer.
•
Where wireless LAN communication is in heavy traffic, your application may falsely recognize
that the communication is disconnected and indicate power off due to response delay. In that
case, disable Power Save to improve the trouble.