Epson TM-T20II UB-R04 Technical Reference Guide - Page 24

Connect the UB-R04 to the TM Printer

Get Epson TM-T20II PDF manuals and user guides View all Epson TM-T20II manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Connect the UB-R04 to the TM Printer 1 Confirm items in the pack. ("Unpacking" on page 19) 2 Remove the two screws of the universal interface connector of the TM Printer and connect the UB-R04, and fix it with two screws. 3 Set the DIP switch of the TM Printer. The interface of the TM printer must be selected as "parallel" with the appropriate settings. If a TM printer that can set the reset signal for pin 31 is used, set to "enable."When using the printer which supports both the USB vendor-defined class and the USB printer class, select the USB vendor-defined class. Refer to the Technical Reference Guide for each TM printer for these settings for details. Also, set the memory switches according to your needs. 4 Power on the printer. Then, after waiting a little, hold down the push button on the interface card for more than 3 seconds. The printer prints the status sheet for the UBR04. You can check all setting values necessary for the network connection. Push button 5 Turn the power switch of the TM Printer on while pressing the Feed button. The printer prints current status of the printer on the paper. 6 Turn off the TM Printer. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
24
Connect the UB-R04 to the TM Printer
1
Confirm items in the pack. (
"Unpacking" on page 19
)
2
Remove the two screws of the universal interface connector of the TM Printer and
connect the UB-R04, and fix it with two screws.
3
Set the DIP switch of the TM Printer. The interface of the TM printer must be selected
as “parallel” with the appropriate settings. If a TM printer that can set the reset signal
for pin 31 is used, set to “enable.” When using the printer which supports both the
USB vendor-defined class and the USB printer class, select the USB vendor-defined
class.
Refer to the Technical Reference Guide for each TM printer for these settings for
details. Also, set the memory switches according to your needs.
4
Power on the printer. Then, after waiting a little, hold down the push button on the
interface card for more than 3 seconds. The printer prints the status sheet for the UB-
R04. You can check all setting values necessary for the network connection.
5
Turn the power switch of the TM Printer on while pressing the Feed button. The
printer prints current status of the printer on the paper.
6
Turn off the TM Printer.
Push button