D-Link DIS-200G Datasheet - Page 241

DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide

237

hybrid

Specifies the port as a hybrid port.

trunk

Specifies the port as a trunk port.

Default

By default, this option is hybrid.

Command Mode

Interface Configuration Mode.

Command Default Level

Level: 15.

Usage Guideline

When a port is set to access mode, this port will be an untagged member of the access VLAN configured for

the port. When a port is set to hybrid mode, the port can be an untagged or tagged member of any VLAN

configured.

When a port is set to trunk mode, this port is either a tagged or untagged member port of its native VLAN and

can be a tagged member of other VLANs configured. The purpose of a trunk port is to support the switch-to-

switch connection.

When the switch-port mode is changed, the VLAN related setting associated with previous mode will be lost.

Example

This example shows how to set the interface eth1/0/1 as a trunk port.

Switch# configure terminal

Switch(config)# interface Ethernet 1/0/1

Switch(config-if)# switchport mode trunk

Switch(config-if)#

43-8

switchport trunk allowed vlan

This command is used to configure the VLANs that are allowed to receive and send traffic on the specified

interface in a tagged format. Use the

no

form of this command to revert to the default setting.

switchport trunk allowed vlan {all | [add | remove | except]

VLAN-ID

[, | -]}

no switchport trunk allowed vlan

Parameters

all

Specifies that all VLANs are allowed on the interface.

add

Specifies to add the specified VLAN list to the allowed VLAN list.

remove

Specifies to remove the specified VLAN list from the allowed VLAN

list.

except

Specifies that all VLANs except the VLANs in the exception list are

allowed.

VLAN-ID

Specifies the allow VLAN list or the VLAN list to be added to or

removed from the allow VLAN list.

Section	Page
1. Introduction	5
2. Basic CLI Commands	13
3. Access Management Commands	19
4. Asymmetric VLAN Commands	26
5. Basic IPv4 Commands	27
6. Basic IPv6 Commands	30
7. Cable Diagnostics Commands	32
8. Digital Diagnostics Monitoring (DDM) Commands	35
9. D-Link Discovery Protocol (DDP) ClientCommands	44
10. DoS Prevention Commands	47
11. Ethernet Ring Protection Switching (ERPS) Commands	50
12. File System Commands	63
13. Filter Database (FDB) Commands	65
14. GARP VLAN Registration Protocol (GVRP) Commands	73
15. IGMP Snooping Commands	80
16. Interface Commands	86
17. IP Utility Commands	94
18. Jumbo Frame Commands	95
19. Link Aggregation Control Protocol (LACP)Commands	96
20. Link Layer Discovery Protocol (LLDP)Commands	100
21. Loopback Detection (LBD) Commands	104
22. Mirror Commands	109
23. MLD Snooping Commands	112
24. Multiple Spanning Tree Protocol (MSTP) Commands	118
25. Power over Ethernet (PoE) Commands	123
26. Power Saving Commands	133
27. Port Security Commands	139
28. Quality of Service (QoS) Commands	144
29. RADIUS Server Commands	152
30. Remote Network MONitoring (RMON) Commands	156
31. Safeguard Engine Commands	164
32. Simple Network Management Protocol(SNMP) Commands	166
33. Spanning Tree Protocol (STP) Commands	184
34. Storm Control Commands	191
35. Surveillance VLAN Commands	194
36. Switch Port Commands	206
37. System File Management Commands	210
38. System Log Commands	218
39. Secure Shell(SSH) Commands	222
40. Time and SNTP Commands	223
41. Time Range Commands	229
42. Traffic Segmentation Commands	233
43. Virtual LAN (VLAN) Commands	235
44. Voice VLAN Commands	245
45. Web Authentication Commands	253
Appendix A - System Log Entries	258
Appendix B - Trap Entries	265

D-Link DIS-200G Datasheet - Page 241

Default, Command Mode, Command Default Level, Usage Guideline, Example, switchport trunk allowed vlan

Page 241 highlights