D-Link DIS-200G Datasheet - Page 220

Example, logging source-interface, Parameters, Default, Command Mode, Command Default Level

Get D-Link DIS-200G PDF manuals and user guides View all D-Link DIS-200G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 220 highlights

DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide The following is a table for the facility. Numerical code 16 17 18 19 20 21 22 23 Facility Local use 0 (local0). Local use 1 (local1). Local use 2 (local2). Local use 3 (local3). Local use 4 (local4). Local use 5 (local5). Local use 6 (local6). Local use 7 (local7). Example This example shows how to enable the logging of system messages with a severity higher than warnings to the remote host 10.10.1.141. Switch# configure terminal Switch(config)# logging server 10.10.1.141 severity warnings Switch(config)# 38-4 logging source-interface This command is used to specify the interface whose IP address will be used as the source address for sending the SYSLOG packet. Use the no form of this command to disabled sending the packet. logging source-interface INTERFACE-ID no logging source-interface Parameters source-interface INTERFACE-ID Specifies the interface whose IP address will be used as the source address of the SYSLOG packet. Default By default, sending the SYSLOG packet is disabled. Command Mode Global Configuration Mode. Command Default Level Level: 15. Usage Guideline Use this command to specify the interface whose IP address will be used as the source address of the SYSLOG packet. The interface MUST be management vlan interface. 216

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
DIS-200G Series Gigabit Ethernet Switch CLI Reference Guide
216
The following is a table for the facility.
Numerical code
Facility
16
Local use 0 (local0).
17
Local use 1 (local1).
18
Local use 2 (local2).
19
Local use 3 (local3).
20
Local use 4 (local4).
21
Local use 5 (local5).
22
Local use 6 (local6).
23
Local use 7 (local7).
Example
This example shows how to enable the logging of system messages with a severity higher than warnings to the
remote host 10.10.1.141.
Switch# configure terminal
Switch(config)# logging server 10.10.1.141 severity warnings
Switch(config)#
38-4
logging source-interface
This command is used to specify the interface whose IP address will be used as the source address for
sending the SYSLOG packet. Use the
no
form of this command to disabled sending the packet.
logging source-interface
INTERFACE-ID
no logging source-interface
Parameters
source-interface
INTERFACE-ID
Specifies the interface whose IP address will be used as the source
address of the SYSLOG packet.
Default
By default, sending the SYSLOG packet is disabled.
Command Mode
Global Configuration Mode.
Command Default Level
Level: 15.
Usage Guideline
Use this command to specify the interface whose IP address will be used as the source address of the
SYSLOG packet. The interface MUST be management vlan interface.