Pioneer CDJ-1000MKII Operating Instructions - Page 30
Copying MMC Data From One MMC to Another
View all Pioneer CDJ-1000MKII manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 30 highlights
ADVANCED OPERATIONS/DÉMARCHES ÉVOLUÉES USING CUE POINTS/LOOP POINTS MEMORY 7 Data other than CUE/LOOP stored on MMC ¶ Hot cue points A, B, C Hot cue points A, B and C are automatically stored on MMC. When a disc storing hot cue points is inserted, the [A], [B] and [C] indicators light in green. To call stored hot cue points, press the A, B or C button. The green flashing indicator will light steadily (when the call is made, sound will be interrupted briefly). If call is not needed, press the HOT CUE REC MODE button. The indicator will change to red, and you can set the hot cue point. To call the hot cue point, remove and replace the disc or MMC and the A, B and C buttons will blink on and off, at this time it is possible to call. ¶ WAVE display When a wave display for one track is completed it is automatically stored on the MMC. When the same track is played again, the stored WAVE display is automatically called. Data for items beyond track number 21 are stored on the MMC. CUE/LOOP MEMORY CUE/LOOP DELETE CUE/LOOP CALL 2, 3 Copying MMC Data (From One MMC to Another) Use the following procedure to copy data on one MMC (CARD A) to another MMC (CARD B). 1. Remove the disc. 2. Remove the card. 3. Hold down the CUE/LOOP MEMORY button for 5 seconds or longer. ¶ [MMC>MMC(OVERWRITE), CARD A IN] is displayed. 4. Insert the MMC to copy data from in the card insertion slot. ¶ [READING] is displayed. 5. After a few minutes, [CARD B IN] is displayed. Remove card A and insert the destination card (CARD B) in the insertion slot. ¶ [WRITING] is displayed. 6. After a few minutes [CARD A IN] is displayed. 7. Repeat steps 4 to 6 twice for a 8M card and four times for a 16M card to complete the copy operation. ¶ [COMPLETE] is displayed when copying is completed. It is impossible to copy from a card with greater capacity to the receiving card. Copying Data in the Internal Memory (Copying from internal memory onto MMC) This procedure copies data in internal memory to MMC. 1. Remove the disc. 2. Remove the card. 3. Hold down the CUE/LOOP MEMORY button for 5 seconds or longer. ¶ [MMC>MMC(OVERWRITE), CARD A IN] is displayed. 4. Press the CUE/LOOP MEMORY button again. ¶ [INT>MMC(OVERWRITE), CARD IN] is displayed. 5. Insert the destination MMC. ¶ [WRITING] is displayed. ¶ [COMPLETE] is displayed when copying is completed. * If the [Err] message appears in one of the displays, the memory data has not been copied properly. Turn the power to both players OFF and then ON again, and repeat the copying procedure from step 1. * When copying from MMC to MMC, or from internal memory to MMC, the MMC memory is overwritten; as a result, any data previously recorded in MMC will be completely erased. * Perform this procedure with the DIGITAL OUT mode set to "DJ". 30 En/Fr UTILISATION DE LA MÉMOIRE DE POINTS DE REPÉRAGE / POINTS DE BOUCLE 7 Données autres que les points CUE/LOOP sur une carte MMC ¶ Points de repérage instantané A, B, C (HOT CUE) sur MMC Les points de repérage instantané A, B et C sont automatiquement mémorisés sur la carte MMC. Quand un disque comportant des points de repérage instantané est inséré, les voyants [A], [B] et [C] s'allument en vert. Pour rappeler ces points, appuyez sur le bouton A, B ou C. Le voyant vert clignotant s'allume de façon continue (quand un rappel est effectué, le son est brièvement interrompu). Si un rappel n'est pas nécessaire, appuyez sur le bouton HOT CUE REC MODE. Le voyant devient rouge et vous pouvez régler le point de repérage instantané. Pour rappeler les points de repérage instantané sur la MMC, retirez et réinsérez le disque ou la MMC: les boutons A, B et C clignoteront. A ce stade, un rappel est possible. ¶ Affichage WAVE Quand un affichage Wave est terminé pour une plage, il est automatiquement mémorisé sur la MMC. Lorsque la même plage est lue à nouveau, l'affichage WAVE mémorisé est automatiquement rappelé. Les données pour les postes audelà du No. 21 sont mémorisées sur la MMC. Copie des données MMC (D'une carte MMC sur une autre) Effectuez les démarches suivantes pour copier une carte MMC (Carte A) sur une autre (Carte B). 1. Retirez le disque. 2. Retirez la carte. 3. Tenez le bouton CUE/LOOP MEMORY enfoncé pendant 5 secondes ou plus. ¶ Le message [MMC>MMC(OVERWRITE), CARD A IN] apparaît. 4. Dans la fente de l'appareil, insérez la carte MMC d'où les données doivent être copiées (carte de source). ¶ Le message [READING] apparaît. 5. Après quelques minutes, le message [CARD B IN] apparaît. Retirez la carte A et insérez la carte de destination (carte B) dans la fente de l'appareil. ¶ Le message [WRITING] apparaît. 6. Après quelques minutes, le message [CARD A IN] apparaît. 7. Répétez les étapes 4 à 6 deux fois pour une carte 8 Mo et quatre fois pour une carte 16 Mo de façon à terminer la copie des données. ¶ Le message [COMPLETE] apparaît quand la copie est terminée. Il est impossible de copier d'une carte ayant une plus grande capacité vers la carte réceptrice. Copie des données dans la mémoire interne (Copie de la mémoire interne vers la carte MMC) Ces démarches vont copier les données de la mémoire interne vers une carte MMC. 1. Retirez le disque. 2. Retirez la carte. 3. Tenez le bouton CUE/LOOP MEMORY enfoncé pendant 5 secondes ou plus. ¶ Le message [MMC>MMC(OVERWRITE), CARD A IN] apparaît. 4. Appuyez à nouveau sur le bouton CUE/LOOP MEMORY. ¶ Le message [INT>MMC(OVERWRITE), CARD IN] apparaît. 5. Insérez la carte MMC de destination. ¶ Le message [WRITING] apparaît. ¶ Le message [COMPLETE] apparaît quand la copie est terminée. * Si le message [Err] apparaît sur un des deux affichages, c'est que les données de la mémoire n'ont pas été correctement copiées. Mettez les deux lecteurs hors tension (OFF), puis sous tension (ON) et recommencez les démarches de la copie depuis l'étape 1. * Lors de la copie d'une carte MMC vers une autre MMC, ou de la mémoire interne vers une carte MMC, le contenu de la carte MMC est écrasé; par conséquent, toute donnée enregistrée auparavant sur la MMC sera complètement effacée. * Effectuez cette démarche après avoir réglé le mode DIGITAL OUT sur "DJ".