Marantz NA-11S1 Owner's Manual in English - Page 18

Setting the network [Network], Connecting wired LAN

Get Marantz NA-11S1 PDF manuals and user guides View all Marantz NA-11S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Preparation Operation Setting the network [Network] • For details on "Quick Setup" operations, see the separate "Getting Started". • If you cancelled "Quick Setup" menu or changed the network environment, perform "Menu" - "Quick Setup". Connecting wired LAN Use this procedure to configure the wired LAN settings. nnNetwork connecting (when "DHCP"settings are "On") When using this unit with the broadband router's DHCP function enabled, this unit automatically performs the IP address setting and other settings. 1 Connect the LAN cable (vpage 8 "Connecting to a home network (LAN)" - "Wired LAN"). 2 Press X (on/standby) to turn on power to the main unit. 3 Press MENU. Turns on the Menu settings mode and the Menu appears on the display (vpage 11 "Menu map"). 4 Use ui and ENTER to select "Network" - "Settings" - "DHCP (On)", then press ENTER or p. "Select DHCP" menu appears. 5 Use ui to select "On", then press ENTER or p. "Setup Ethernet" menu appears. 6 Use ui to select "Test Connection", then press ENTER or p. "Wait for the network to connect..." is displayed, and the unit starts connecting to the LAN. • When the connection is made successfully, "Connected!" appears. • If the connection cannot be established, "Connection Failed" is displayed. Perform steps 1 - 6 again. You may need to set the network connection manually, depending on the provider you use. To set the connection manually, use the setting procedure of "Network connecting (when "DHCP" settings are "Off")". nnNetwork connecting (when "DHCP" settings is "Off") This section explains the settings when connecting this unit to a network that does not have a DHCP function. To configure the settings manually, check the setting details with your network administrator. 1 Perform steps 1 - 4 of the "Network connecting (when "DHCP" settings are "On")" procedure and select "Off" in step 5. "Setup Ethernet" menu appears. 2 Use ui to select "IP Address", then press ENTER or p. "Enter IP Address" menu appears. 3 Use uip or 0 - 9 to input the IP address and press ENTER. 4 Use uip or 0 - 9 to input the address for "Subnet Mask", "Gateway", "Primary DNS", and "Secondary DNS". 5 Use ui to select "Test Connection", then press ENTER or p. "Wait for the network to connect..." is displayed, and the unit starts connecting to the LAN. • When the connection is made successfully, "Connected!" appears. • If the connection cannot be established, "Connection Failed" is displayed. Perform steps 1 - 5 again. Information 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
15
Setting the network [Network]
•
For details on “Quick Setup” operations, see the separate
“Getting Started”.
•
If you cancelled “Quick Setup” menu or changed the
network environment, perform “Menu” – “Quick Setup”.
Connecting wired LAN
Use this procedure to configure the wired LAN settings.
n
Network connecting
(when “DHCP”settings are “On”)
When using this unit with the broadband router’s DHCP
function enabled, this unit automatically performs the IP
address setting and other settings.
1
Connect
the
LAN
cable
(
v
page  8
“Connecting to a
home network (LAN)” – “Wired
LAN”).
2
Press
X
(on/standby) to turn on
power to the main unit.
3
Press
MENU
.
Turns on the Menu settings mode
and the Menu appears on the
display
(
v
page 
11
“Menu
map”).
4
Use
ui
and
ENTER
to select “Network” –
“Settings” – “DHCP (On)”, then press
ENTER
or
p
.
“Select DHCP” menu appears.
5
Use
ui
to select “On”, then press
ENTER
or
p
.
“Setup Ethernet” menu appears.
6
Use
ui
to select “Test Connection”, then press
ENTER
or
p
.
“Wait for the network to connect...” is displayed, and
the unit starts connecting to the LAN.
•
When the connection is made successfully, “Connected!”
appears.
•
If the connection cannot be established, “Connection
Failed” is displayed. Perform steps 1 – 6 again.
You may need to set the network connection manually,
depending on the provider you use. To set the connection
manually, use the setting procedure of “Network connecting
(when “DHCP” settings are “Off”)”.
n
Network connecting
(when “DHCP” settings is “Off”)
This section explains the settings when connecting this unit
to a network that does not have a DHCP function.
To configure the settings manually, check the setting details
with your network administrator.
1
Perform steps 1
–
4 of the
“Network connecting (when
“DHCP” settings are “On”)”
procedure and select “Off” in
step 5.
“Setup Ethernet” menu appears.
2
Use
ui
to select “IP Address”,
then press
ENTER
or
p
.
“Enter IP Address” menu appears.
3
Use
uip
or
0 – 9
to input the
IP address and press
ENTER
.
4
Use
uip
or
0 – 9
to input the address for
“Subnet Mask”, “Gateway”, “Primary DNS”, and
“Secondary DNS”.
5
Use
ui
to select “Test Connection”, then press
ENTER
or
p
.
“Wait for the network to connect...” is displayed, and
the unit starts connecting to the LAN.
•
When the connection is made successfully, “Connected!”
appears.
•
If the connection cannot be established, “Connection
Failed” is displayed. Perform steps 1 – 5 again.