Marantz NA-11S1 Owner's Manual in English - Page 15

Setting the first setup [Quick Setup], General Settings [General], Language, Auto-Standby, Firmware - firmware update

Get Marantz NA-11S1 PDF manuals and user guides View all Marantz NA-11S1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Preparation Operation Setting the first setup [Quick Setup] • For details on "Quick Setup" operations, see the separate "Getting Started". • If you cancelled "Quick Setup" menu or changed the network environment, perform "Menu" - "Quick Setup". General Settings [General] Language Sets the language for display the menu. • The default setting is "English". 1 Press MENU. Turns on the Menu settings mode and the Menu appears on the display (vpage 11 "Menu map"). 2 Use ui and ENTER to select "General" - "Language", then press ENTER or p. English / Français / Español Auto-Standby When this unit is in the stop state and there is no input signal and operation for 30 minutes, it automatically enters the standby mode. • The default setting is "On". 1 Press MENU. Turns on the Menu settings mode and the Menu appears on the display (vpage 11 "Menu map"). 2 Use ui and ENTER to select "General" - "Auto-Standby", then press ENTER or p. "Select Auto-Standby" menu appears. 3 Use ui to select "On" or "Off", then press ENTER or p. The setting is entered. NOTE In the following situations, the Auto-Standby function does not operate. • When the source is "iPod" (Direct mode) or "AirPlay". Firmware General Settings [General] nnUpdate • In order to update the firmware, the environment and settings required for connecting to broadband internet are needed (vpage 8). • Perform the firmware update operation after at least 2 minutes has elapsed since turning this unit's power ON. 1 Press MENU. Turns on the Menu settings mode and the Menu appears on the display (vpage 11 "Menu map"). 2 Use ui and ENTER to select "General" - "Firmware" - "Update", then press ENTER or p. Check For Update Check for firmware updates. You can also check approximately how long it will take to complete an update. Update Start Execute the update process. • If updating fails, the set automatically retries, but if updating is still not possible, one of the messages shown below is displayed. If the display reads as shown below, check the settings and network environment, then update again. Display Updating fail Login failed Server is busy Connection fail Download fail Description Updating failed. Failure to login to server. Server is busy. Wait a while then try again. Failure in connecting to server. Downloading of the firmware has failed. Information 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
12
General Settings [General]
Language
Sets the language for display the menu.
•
The default setting is “English”.
1
Press
MENU
.
Turns on the Menu settings mode
and the Menu appears on the
display
(
v
page 
11
“Menu
map”).
2
Use
ui
and
ENTER
to select
“General” – “Language”, then
press
ENTER
or
p
.
English
/
Français
/
Español
Auto-Standby
When this unit is in the stop state and there is no input signal
and operation for 30 minutes, it automatically enters the
standby mode.
•
The default setting is “On”.
1
Press
MENU
.
Turns on the Menu settings mode
and the Menu appears on the
display
(
v
page 
11
“Menu
map”).
2
Use
ui
and
ENTER
to select
“General”
–
“Auto-Standby”,
then press
ENTER
or
p
.
“Select
Auto-Standby”
menu
appears.
3
Use
ui
to select “On” or “Off”,
then press
ENTER
or
p
.
The setting is entered.
NOTE
In the following situations, the Auto-Standby function does not
operate.
•
When the source is “iPod” (Direct mode) or “AirPlay”.
Firmware
n
Update
•
In order to update the firmware, the environment and
settings required for connecting to broadband internet are
needed (
v
page 8
).
•
Perform the firmware update operation after at least 2
minutes has elapsed since turning this unit’s power ON.
1
Press
MENU
.
Turns on the Menu settings mode
and the Menu appears on the
display
(
v
page 
11
“Menu
map”).
2
Use
ui
and
ENTER
to select
“General”
–
“Firmware”
–
“Update”, then press
ENTER
or
p
.
Check For Update
Check for firmware updates. You can also
check approximately how long it will take
to complete an update.
Update Start
Execute the update process.
•
If updating fails, the set automatically retries, but if updating
is still not possible, one of the messages shown below is
displayed. If the display reads as shown below, check the
settings and network environment, then update again.
Display
Description
Updating fail
Updating failed.
Login failed
Failure to login to server.
Server is busy
Server is busy. Wait a while then try
again.
Connection fail
Failure in connecting to server.
Download fail
Downloading of the firmware has failed.
General Settings [General]
Setting the first setup
[Quick Setup]
•
For details on “Quick Setup” operations, see the separate
“Getting Started”.
•
If you cancelled “Quick Setup” menu or changed the
network environment, perform “Menu” – “Quick Setup”.