Lantronix MatchPort b/g MatchPort b/g - User Guide - Page 58

Flush Mode, Disconnect Mode Option, Function

Get Lantronix MatchPort b/g PDF manuals and user guides View all Lantronix MatchPort b/g manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

5: Configuration via Serial Mode or Telnet Port Disconnect Mode Option Disconnect with EOT (^D) (5) 7 6 5 4 3 2 1 0 1 (1) The MatchPort sends the "Terminal Type" upon an outgoing connection. (2) A password is required for a connection to the serial port from the network. (3) The TCP connection closes even if the remote site does not acknowledge the disconnection. (4) When there is a network connection to or from the serial port, the state LED turns off instead of blinking. (5) When Ctrl+D or Hex 04 is detected, the connection is dropped. Both Telnet Com Port Cntrl and Disconnect with EOT must be enabled for Disconnect with EOT to function properly. Ctrl+D is only detected going from the serial port to the network. (6) When Modem Control In transitions from a high state to a low state, the network connection to or from the serial port drops. Flush Mode The FlushMode (buffer flushing) parameter controls line handling and network buffers with connection startup and disconnect. FlushMode ( 0) ? _ Select between two different packing algorithms (the current configuration displays within the parentheses). Note: All bit positions in the table that are blank represent "don't care" bits for that particular option, which can be set to either a 0 or 1 value. Available Flush Mode options are: Table 5-11. Flush Mode Options Function Input Buffer (Serial to Network) Clear with a connection that is initiated from the device to the network Clear with a connection initiated from the network to the device Clear when the network connection to or from the device is disconnected Output Buffer (Network to Serial) Clear with a connection that is initiated from the device to the network Clear with a connection initiated from the network to the device Clear when the network connection to or from the device is disconnected Alternate Packing Algorithm (Pack Control) Enable 7 6 5 4 3 2 1 0 1 1 1 1 1 1 1 MatchPort User Guide 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
5: Configuration via Serial Mode or Telnet Port
Disconnect Mode Option
7
6
5
4
3
2
1
0
Disconnect with EOT (^D)
(5)
1
(1) The MatchPort sends the "Terminal Type" upon an outgoing connection.
(2) A password is required for a connection to the serial port from the network.
(3) The TCP connection closes even if the remote site does not acknowledge the disconnection.
(4) When there is a network connection to or from the serial port, the state LED turns off instead of blinking.
(5) When
Ctrl+D
or
Hex 04
is detected, the connection is dropped. Both
Telnet Com Port Cntrl
and
Disconnect with EOT
must be enabled for
Disconnect with EOT
to function properly.
Ctrl+D
is only
detected going from the serial port to the network.
(6) When
Modem Control In
transitions from a high state to a low state, the network connection to or from the
serial port drops.
Flush Mode
The FlushMode (buffer flushing) parameter controls line handling and network buffers
with connection startup and disconnect.
FlushMode ( 0) ? _
Select between two different packing algorithms (the current configuration displays
within the parentheses).
Note:
All bit positions in the table that are blank represent “don’t care” bits for
that particular option, which can be set to either a 0 or 1 value.
Available Flush Mode options are:
Table 5-11. Flush Mode Options
Function
7
6
5
4
3
2
1
0
Input Buffer (Serial to Network)
Clear with a connection that is initiated from the
device to the network
1
Clear with a connection initiated from the network
to the device
1
Clear when the network connection to or from the
device is disconnected
1
Output Buffer (Network to Serial)
Clear with a connection that is initiated from the
device to the network
1
Clear with a connection initiated from the network
to the device
1
Clear when the network connection to or from the
device is disconnected
1
Alternate Packing Algorithm (Pack Control)
Enable
1
MatchPort User Guide
58