Hoveround Teknique XHD User Manual - Page 52

Hoveround Teknique XHD Manual

Get Hoveround Teknique XHD PDF manuals and user guides View all Hoveround Teknique XHD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Chapter 11 Appendixes Appendix A: Programmable Parameters The controller used on your power wheelchair is programmable for basic functions. It requires a programmer to make changes. Any changes must be made by a qualified technician only. The following chart indicates the standard program values of the factory settings. Refer to the appropriate section depending on the style of control system on your chair. Any subsequent change of the programmed values should be recorded and saved for future reference. Program Settings Program Settings Forward Speed Max Forward Speed Min Forward Acceleration Forward Deceleration Reverse Speed Max Reverse Speed Min Turning Speed Max Turning Speed Min Turning Acceleration Turning Deceleration TEK FWD VSI VR2 85 75 10 20 30 20 50 65 55 50 10 20 15 15 10 10 10 10 20 70 TEK RWD ALL 100 10 30 50 55 10 20 10 30 20 TEK XHD VSI / VR2 85 10 30 50 50 10 15 10 20 20 TEK HD-6 VR2 70 10 30 50 50 20 15 10 20 50 TEK GT Pilot+ VR2 100 100 25 20 20 30 50 70 55 50 10 20 25 17 25 10 5 15 5 70 52 Chapter 11 D82007778 REV N 7/10/12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
52
Chapter 11
D82007778 REV N 7/10/12
Chapter 11
Appendixes
Appendix A:
Programmable Parameters
The controller used on your power wheelchair is programmable for basic functions.
It requires a programmer to make changes. Any changes must be made by a
qualified technician only.
The following chart indicates the standard program values of the factory settings.
Refer to the appropriate section depending on the style of control system on your
chair. Any subsequent change of the programmed values should be recorded and
saved for future reference.
Program Settings
TEK FWD
TEK RWD
TEK XHD
TEK HD-6
TEK GT
Program Settings
VSI
VR2
ALL
VSI / VR2
VR2
Pilot+
VR2
Forward Speed Max
85
75
100
85
70
100
100
Forward Speed Min
10
20
10
10
10
25
20
Forward Acceleration
30
20
30
30
30
20
30
Forward Deceleration
50
65
50
50
50
50
70
Reverse Speed Max
55
50
55
50
50
55
50
Reverse Speed Min
10
20
10
10
20
10
20
Turning Speed Max
15
15
20
15
15
25
17
Turning Speed Min
10
10
10
10
10
25
10
Turning Acceleration
10
10
30
20
20
5
15
Turning Deceleration
20
70
20
20
50
5
70