Hoveround Teknique XHD User Manual - Page 47

Removal and installation of seats with side rails

Get Hoveround Teknique XHD PDF manuals and user guides View all Hoveround Teknique XHD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Removal and installation of seats with side rails The seat assembly is heavy. To avoid injury, do not attempt to lift beyond your capability. Front Bolt Rear Bolt Removal Figure 9C 1. Remove the controller (See page 46). 2. Remove the controller cable from seat if so attached. 3. Locate the front and rear bolts on each of the side brackets below the seat (See Figure 9C). 4. Remove the front bolts, leave the rear bolts installed but loose. Note the position of the bolts for reinstallation. 5. From the rear, tilt the seat back and remove from the rear slots. Replacement 1. Locate the rear mounting holes on the brackets attached to the seat. If bolt has been removed, loosely install it in the same position prior to removal of the seat. 2. Locate the controller cable to the rear of the chair and between the side rails. 3. From the rear, lift the seat, placing the rear bolts into the slots in the rear of the frame bracket and allow the seat to rest in the forward position on the base frame. 4. Locate the front mounting holes in the side rails and install the front bolts and tighten the front and rear bolts. 5. Reinstall the controller cable and controller mounting bracket. Position the cable to the minimum length to allow the arm to lift. To prevent cable damage, do not let the cable hang free or extend beyond the chair. Use care when driving to keep the cable from catching on objects. D82007778 REV N 7/10/12 Chapter 9 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Removal and installation of seats with side rails
Figure 9C
Removal
1.
Remove the controller (See page 46).
2.
Remove the controller cable from seat if so attached.
3.
Locate the front and rear bolts on each of the side brackets below the seat
(See Figure 9C).
4.
Remove the front bolts, leave the rear bolts installed but loose. Note the
position of the bolts for reinstallation.
5.
From the rear, tilt the seat back and remove from the rear slots.
Replacement
1.
Locate the rear mounting holes on the brackets attached to the seat. If bolt
has been removed, loosely install it in the same position prior to removal of
the seat.
2.
Locate the controller cable to the rear of the chair and between the side rails.
3.
From the rear, lift the seat, placing the rear bolts into the slots in the rear of
the frame bracket and allow the seat to rest in the forward position on the
base frame.
4.
Locate the front mounting holes in the side rails and install the front bolts and
tighten the front and rear bolts.
5.
Reinstall the controller cable and controller mounting bracket. Position the
cable to the minimum length to allow the arm to lift. To prevent cable damage,
do not let the cable hang free or extend beyond the chair. Use care when driving
to keep the cable from catching on objects.
D82007778 REV N 7/10/12
Chapter 9
47
The seat assembly is heavy. To avoid injury, do not attempt to lift
beyond your capability.
Front Bolt
Rear Bolt