D-Link DBG-2000 Product Manual 1 - Page 64

Destination IP address

Get D-Link DBG-2000 PDF manuals and user guides View all D-Link DBG-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

DBG-2000 User Guide The fields available on this page are as follows: Field Name Destination IP address Subnet mask Gateway IP address Interface Metric Private Save Cancel Description Enter the name of the route. Enter the IP address of the static route's destination. Enter the subnet mask of the static route. Enter the IP address of the gateway through which the destination host or network can be reached. Select a physical network interface (WAN, DMZ, VLAN, or LAN) through which this route is accessible. Enter a value between 2 and 15. It determines the priority of the route. If multiple routes to the same destination exist, the route with the lowest metric is chosen. Enable this feature to make this route private. If the route is made private, the route will not be shared in a RIP. Click Save to save your settings. Click Cancel to revert to the previous settings. Policy Route Policy routes are useful when the Load Balancing feature is in use. Selecting TCP/UDP, you can assign the type of traffic to go over the specified WAN ports. The source network, source address, the destination network, a destination address, service, or protocol can be associated with a particular WAN port for increased flexibility. For example, the VoIP traffic for a set of LAN IP addresses can be assigned to one WAN, and any VoIP traffic from the remaining IP addresses can be assigned to the other WAN link. Policy routes are only applicable when load balancing mode is enabled and more than one WAN is configured. This section of the routing shows a list of configured policy routes on the gateway with the following details: Field Name Protocol Source network Source port Destination network Description It displays the name of the policy route. It displays the protocol placed in the transport layers of the Internet protocol suite. It displays the source network. It options are Any, an IP address, and a range of IP address. It displays a source port for which the policy route will be applicable. It displays the destination network. Its options are Any, an IP address, and a range of IP addresses. 64

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
The fields available on this page are as follows:
Field
Description
Name
Enter the name of the route.
Destination IP address
Enter the IP address of the static route’s destination.
Subnet mask
Enter the subnet mask of the static route.
Gateway IP address
Enter the IP address of the gateway through which the destination host or network can be
reached.
Interface
Select a physical network interface (WAN, DMZ, VLAN, or LAN) through which this route is
accessible.
Metric
Enter a value between 2 and 15. It determines the priority of the route. If multiple routes to
the same destination exist, the route with the lowest metric is chosen.
Private
Enable this feature to make this route private. If the route is made private, the route will not
be shared in a RIP.
Save
Click
to save your settings.
Save
Cancel
Click
to revert to the previous settings.
Cancel
Policy Route
Policy routes are useful when the Load Balancing feature is in use. Selecting TCP/UDP, you can assign the type of traffic to go over the specified
WAN ports. The source network, source address, the destination network, a destination address, service, or protocol can be associated with a
particular WAN port for increased flexibility.
For example, the VoIP traffic for a set of LAN IP addresses can be assigned to one WAN, and any VoIP traffic from the remaining IP addresses
can be assigned to the other WAN link. Policy routes are only applicable when load balancing mode is enabled and more than one WAN is
configured.
This section of the routing shows a list of configured policy routes on the gateway with the following details:
Field
Description
Name
It displays the name of the policy route.
Protocol
It displays the protocol placed in the transport layers of the Internet protocol suite.
Source network
It displays the source network. It options are Any, an IP address, and a range of IP address.
Source port
It displays a source port for which the policy route will be applicable.
Destination network
It displays the destination network. Its options are Any, an IP address, and a range of IP
addresses.
DBG-2000 User Guide
64