Campbell Scientific AVW200 AVW200-series Vibrating Wire Interfaces - Page 37

Measurement, AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules,

Get Campbell Scientific AVW200 PDF manuals and user guides View all Campbell Scientific AVW200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules 5.2.2 Measurement The Deployment/Measurement Tab is used to configure the SDI-12 Address, multiplexer type, begin frequency, end frequency, and excitation (see FIGURE 5-3). FIGURE 5-3. Deployment/Measurement Tab in DevConfig NOTE The Begin Frequency, End Frequency, and excitation parameters in DevConfig are only used for the RS-232 (terminal commands) and SDI-12 communication modes. When using the RS-232 (PakBus) or RF (PakBus) communication modes, the settings for the Begin Frequency, End Frequency, and excitation parameters are entered in the AVW200() CRBasic instruction (see Section 6, Programming). Description of the Measurement Settings follows: SDI-12 Address-select an address if using SDI-12. Otherwise use the default value of 0. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
5.2.2 Measurement
The Deployment/Measurement Tab is used to configure the SDI-12 Address,
multiplexer type, begin frequency, end frequency, and excitation (see FIGURE
5-3).
FIGURE 5-3.
Deployment/Measurement Tab in DevConfig
The Begin Frequency, End Frequency, and excitation parameters
in DevConfig are only used for the RS-232 (terminal commands)
and SDI-12 communication modes.
When using the RS-232
(PakBus) or RF (PakBus) communication modes, the settings for
the Begin Frequency, End Frequency, and excitation parameters
are entered in the AVW200() CRBasic instruction (see Section 6,
Programming
).
Description of the Measurement Settings follows:
SDI-12 Address
—select an address if using SDI-12.
Otherwise use the default
value of 0.
NOTE
29