Campbell Scientific AVW200 AVW200-series Vibrating Wire Interfaces - Page 35

AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules,

Get Campbell Scientific AVW200 PDF manuals and user guides View all Campbell Scientific AVW200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules FIGURE 5-2. Deployment Communications Editor in DevConfig NOTE Certain AVW206 settings must match the RF401 settings for communications between the interface and radio to be successful. Description of the Communication Settings follows: Protocol-choose "PakBus" for the "Protocol" setting. Please note that the "Protocol" setting for the RF401-series radio must be set to either "PakBus Aware" or "PakBus Node" for communications to be successful. PakBus Address-enter a PakBus Address that matches the PakBus address specified in the CRBasic program that will control the AVW200. Each device in a PakBus network must have a unique address. Valid settings are 1 - 4094. RS-232 Baud Rate-enter the baud rate in which you want to communicate. Hop Sequence-enter the radio "Hop Sequence" that matches all of the RF401 radios and other AVW206 Interfaces in the network. Valid entries are 0-6. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
AVW200-series 2-Channel Vibrating Wire Spectrum Analyzer Modules
FIGURE 5-2.
Deployment Communications Editor in DevConfig
Certain AVW206 settings must match the RF401 settings for
communications between the interface and radio to be successful.
Description of the Communication Settings follows:
Protocol
—choose "PakBus" for the “Protocol” setting.
Please note that the
“Protocol” setting for the RF401-series radio must be set to either “PakBus
Aware” or “PakBus Node” for communications to be successful.
PakBus Address
—enter a PakBus Address that matches the PakBus address
specified in the CRBasic program that will control the AVW200.
Each device
in a PakBus network must have a unique address.
Valid settings are 1 - 4094.
RS-232 Baud Rate
—enter the baud rate in which you want to communicate.
Hop Sequence
—enter the radio ”Hop Sequence” that matches all of the RF401
radios and other AVW206 Interfaces in the network. Valid entries are 0-6.
NOTE
27