URC MX-350 Owners Manual - Page 15

Recalling Pre-Programmed Settings, Cloning One MX-350 to Another - programming universal remote

Get URC MX-350 PDF manuals and user guides View all URC MX-350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

The MX-350 Erasing the Entire MX-350 To erase EVERYTHING, press and hold both the MAIN and the STOP buttons for 15 seconds. After 15 seconds, the RESET screen appears. Press the SURE button to erase all of your settings and return to the factory default setup. SURE Button Cloning One MX-350 to Another If you own two or more MX-350, you can copy and transfer all the setup from one MX-350 to another. Just follow these easy steps: 1 Enter SETUP mode by pressing and holding both MAIN and ENT for three seconds. Note: You have 30 seconds for each step, otherwise the MX-350 will time out automatically. 2 Press a PAGE button to display page two of Setup. 3 Press the CLONE button. 4 Align the two MX-350 head-to-head, about an inch apart. 5 Press the RECV display button on the new MX-350 you would like to setup by cloning. 6 Press the SEND display button on the MX-350 you previously setup. 7 Press the START button on the new MX-350 and then press the START button on the MX-350 you previously setup. Note: Cloning typically takes about 90 seconds. After completion, the cloned MX-350 will flash "GOOD". 8 Return to normal operation by pressing the MAIN button twice. 26 Universal Remote Control, Inc. Recalling Pre-Programmed Settings If you didn't write down the code numbers you setup your MX-350 with, you can recall them via this simple process: 1 Enter SETUP mode by pressing and holding both MAIN and ENT for three seconds. Note: You have 30 seconds for each step, otherwise the MX-350 will time out automatically. 2 Go to page two of the SETUP menu via the PAGE UP button. 3 Press the RECAL button. The display changes to the recall screens. The screen automatically switches between four screens, alternately flashing page one devices and code numbers then those for page two. Note: Pay attention to the page numbers on the bottom of the screen. Page 1 code numbers are the ones setup for the Page1 Devices. Page 2 code numbers are the ones setup for the Page 2 Devices. 4 Write down the code numbers as they appear. 5 Return to normal operation by pressing the MAIN button twice. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
27
Recalling Pre-Programmed Settings
If you didn’t write down the code numbers you setup your MX-350 with,
you can recall them via this simple process:
Enter SETUP mode by pressing and holding both MAIN and ENT
for three seconds.
Note:
You have 30 seconds for each step, otherwise the MX-350 will time
out automatically.
Go to page two of the SETUP menu via the PAGE UP button.
Press the RECAL button. The display changes to the recall screens. The
screen automatically switches between four screens, alternately flash-
ing page one devices and code numbers then those for page two.
Note:
Pay attention to the page numbers on the bottom of the screen. Page
1 code numbers are the ones setup for the Page1 Devices. Page 2 code
numbers are the ones setup for the Page 2 Devices.
Write down the code numbers as they appear.
Return to normal operation by pressing the MAIN button twice.
26
Erasing the Entire MX-350
To erase EVERYTHING, press and hold both the MAIN and the STOP
buttons for 15 seconds. After 15 seconds, the RESET screen appears.
Press the SURE button to erase all of your settings and return to the fac-
tory default setup.
Cloning One MX-350 to Another
If you own two or more MX-350, you can copy and transfer all the setup
from one MX-350 to another. Just follow these easy steps:
Enter SETUP mode by pressing and holding both MAIN and ENT
for three seconds.
Note:
You have 30 seconds for each step, otherwise the MX-350 will time
out automatically.
Press a PAGE button to display page two of Setup.
Press the CLONE button.
Align the two MX-350 head-to-head, about an inch apart.
Press the RECV display button on the new MX-350 you would like to
setup by cloning.
Press the SEND display button on the MX-350 you previously setup.
Press the START button on the new MX-350 and then press the
START button on the MX-350 you previously setup.
Note:
Cloning typically takes about 90 seconds.
After completion, the cloned MX-350 will flash “GOOD”.
Return to normal operation by pressing the MAIN button twice.
The MX-350
SURE
Button
1
2
3
4
5
6
7
8
1
2
3
4
5
Universal Remote Control, Inc.
OCE-0024B_Rev05
2007.3.9 9:36 AM
페이지26